Incorrect codes are a form of output error for a digital-to-analog converter (DA

CuriousTab

C Programming C# Programming C++ Programming Database Java Programming Networking

Biochemical Engineering Biochemistry Biotechnology Chemical Engineering Civil Engineering Computer Science Digital Electronics Electrical Engineering Electronics Electronics and Communication Engineering Mechanical Engineering Microbiology Technical Drawing

Current Affairs General Knowledge

Data Interpretation Logical Reasoning Non Verbal Reasoning Verbal Ability Verbal Reasoning

AIEEE Bank Exams CAT GATE IIT JEE TOEFL

Analyst Bank PO Database Administrator IT Trainer Network Engineer Project Manager Software Architect

Discussion

Home ‣ Electronics ‣ Analog and Digital Converters Comments

Question
Incorrect codes are a form of output error for a digital-to-analog converter (DAC).
Options
A. True
B. False

Correct Answer

False

Analog and Digital Converters problems

Search Results

1. The bits of a number that tell how large the number is are called ____________________.
Options
A. carry bits
B. magnitude bits
C. sign bits
D. most significant bits

Discuss

Correct Answer: magnitude bits

2. The 1's complement of 101010₂ is _________.
Options
A. 010110₂
B. 010101₂
C. 110111₂
D. 101011₂

Discuss

Correct Answer: 010101₂

3. One advantage of using the 2's complement system to represent signed numbers is that you ___________.
Options
A. can perform subtraction by performing addition
B. can perform addition by performing subtraction
C. can perform division through repeated subtraction
D. none of the above

Discuss

Correct Answer: can perform subtraction by performing addition

4. Two 4-bit adders could be cascaded to form a(n) ___________.
Options
A. 16-bit parallel-adder circuit
B. 8-bit parallel-adder circuit
C. full-adder circuit
D. arithmetic-logic unit

Discuss

Correct Answer: 8-bit parallel-adder circuit

5. In binary number systems the sign of a number is indicated by _________.
Options
A. using a 0 (zero) bit in front of negative numbers
B. inverting the bits if the number is negative
C. including a sign bit along with the magnitude bits
D. placing a negative sign in front of the number

Discuss

Correct Answer: including a sign bit along with the magnitude bits

6. The key advantage of the successive approximation analog-to-digital converter (ADC) is its conversion speed.
Options
A. True
B. False

Discuss

Correct Answer: True

7. In a binary-weighted digital-to-analog converter (DAC), the values of the input resistors are chosen to be proportional to the binary weights of the corresponding input bits.
Options
A. True
B. False

Discuss

Correct Answer: False

8. A sample-and-hold circuit samples an analog value and holds it long enough for the analog-to-digital conversion to occur.
Options
A. True
B. False

Discuss

Correct Answer: True

9. The relative accuracy of a digital-to-analog converter (DAC) is determined by settling time.
Options
A. True
B. False

Discuss

Correct Answer: False

10. One way to determine the resolution of a digital-to-analog converter (DAC) is to compare the ratio of one step voltage to the maximum output voltage.
Options
A. True
B. False

Discuss

Correct Answer: True

Comments

Enter a new Comment

More in Electronics:

Alternating Current and Voltage Alternating Current vs Direct Current Analog and Digital Converters Analog to Digital Arithmetic Operations and Circuits Basic Op-Amp Circuits Bipolar Junction Transistors (BJT)Capacitors Combinational Logic Circuits Computer Hardware and Software Diodes and Applications Field Effect Transistors (FET)Flip-Flops and Timers Inductors Logic Circuit Simplification Logic Gates Magnetism and Electromagnetism Measurement, Conversion and Control Number Systems and Codes Ohm's Law Operational Amplifiers Parallel Circuits Programmable Logic Devices (PLD)Quantities and Units RC Circuits Resistance and Power RL Circuits RLC Circuits and Resonance Semiconductor Memory Semiconductor Principles Sequential Logic Circuits Series-Parallel Circuits Series Circuits Special-Purpose Op-Amp Circuits Standard Logic Devices (SLD)Testing and Troubleshooting Thyristors and Tranducers Time Response of Reactive Circuits Transformers Transistors and Applications Voltage and Current

Aptitude

Time and Distance
Volume and Surface Area
Problem on Trains
Permutation and Combination

Engineering

Civil Engineering
Computer Science
Mechanical Engineering
Technical Drawing

Programming

C Programming
C# Programming
C++ Programming
Java Programming

Reasoning

Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning

CuriousTab

CuriousTab

Discussion

Incorrect codes are a form of output error for a digital-to-analog converter (DAC).

Analog and Digital Converters problems

Search Results

More in Electronics:

Aptitude

Engineering

Programming

Reasoning

Links

Social