Discussion
Home ‣ Civil Engineering ‣ RCC Structures Design Comments
- Question
If the depth of actual neutral axis of a doubly reinforced beam
Options- A. is greater than the depth of critical neutral axis, the concrete attains its maximum stress earlier
- B. is less than the depth of critical neutral axis, the steel in the tensile zone attains its maximum stress earlier
- C. is equal to the depth of critical neutral axis, the concrete and steel attain their maximum stresses simultanesouly
- D. all the above.
- Correct Answer
- all the above.
- 1. The shear reinforcement in R.C.C. is provided to resist
Options- A. vertical shear
- B. horizontal shear
- C. diagonal compression
- D. diagonal tension. Discuss
- 2. Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam
Options- A. are curtailed if not required to resist the bending moment
- B. are bent up at suitable places to serve as shear reinforcement
- C. are bent down at suitable places to serve as shear reinforcement
- D. are maintained at bottom to provide at least local bond stress. Discuss
- 3. To ensure uniform pressure distribution, the thickness of the foundation, is
Options- A. kept uniform throughout
- B. increased gradually towards the edge
- C. decreased gradually towards the edge
- D. kept zero at the edge. Discuss
- 4. An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm ? placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is
Options- A. 49.9 kg/cm2
- B. 100 kg/cm2
- C. 250 kg/cm2
- D. 175 kg/cm2 Discuss
- 5. The horizontal portion of a step in a stairs case, is known as
Options- A. rise
- B. flight
- C. winder
- D. tread. Discuss
- 6. The weight of a foundation is assumed as
Options- A. 5% of wall weight
- B. 7% of wall weight
- C. 10% of wall weight
- D. 12% of wall weight Discuss
- 7. The maximum diameter of a bar used in a ribbed slab, is
Options- A. 12 mm
- B. 6 mm
- C. 20 mm
- D. 22 mm
- E. 24 mm Discuss
- 8. If bending moment is M, shear force is F effecive depth is d, lever arm is la area of reinforcement is As and sum of the circumferences of main reinforcement is 0, the bond stress based on working stress method, is
Options- A.
- B.
- C.
- D.
Discuss
- 9. A reinforced concrete cantilever beam is 3.6 m long, 25 cm wide and has its lever arm 40 cm. It carries a load of 1200 kg at its free end and vertical stirrups can carry 1800 kg. Assuming concrete to carry one-third of the diagonal tension and ignoring the weight of the beam, the number of shear stirrups required, is
Options- A. 30
- B. 35
- C. 40
- D. 45
- E. 50 Discuss
- 10. A T-beam behaves as a rectangular beam of a width equal to its flange if its neutral axis
Options- A. remains within the flange
- B. remains below the slab
- C. coincides the geometrical centre of the beam
- D. none of these. Discuss
RCC Structures Design problems
Search Results
Correct Answer: diagonal tension.
Correct Answer: are bent down at suitable places to serve as shear reinforcement
Correct Answer: decreased gradually towards the edge
Correct Answer: 49.9 kg/cm2
Correct Answer: tread.
Correct Answer: 10% of wall weight
Correct Answer: 22 mm
Correct Answer:
Correct Answer: 40
Correct Answer: remains within the flange
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.