You have the following routing table. Which of the following networks will not be placed in the neighbor routing table? R 192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 C 192.168.40.0/24 is directly connected, Serial0 172.16.0.0/24 is subnetted, 1 subnets C 172.16.30.0 is directly connected, Loopback0 R 192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 R 10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0 C 192.168.50.0/24 is directly connected, Ethernet0

172.16.30.0
192.168.30.0
10.0.0.0
All of them will be placed in the neighbor routing table.

Correct Answer: 10.0.0.0

Explanation:

The network 10.0.0.0 cannot be placed in the next router's routing table because it already is at 15 hops. One more hop would make the route 16 hops, and that is not valid in RIP networking.

← Previous Question Next Question→

More Questions from IP Routing

A network administrator views the output from the show ip route command. A network that is advertised by both RIP and IGRP appears in the routing table flagged as an IGRP route. Why is the RIP route to this network not used in the routing table?
Two connected routers are configured with RIP routing. What will be the result when a router receives a routing update that contains a higher-cost path to a network already in its routing table?
Which two of the following are true regarding the distance-vector and link-state routing protocols? Link state sends its complete routing table out all active interfaces on periodic time intervals. Distance vector sends its complete routing table out all active interfaces on periodic time intervals. Link state sends updates containing the state of its own links to all routers in the internetwork. Distance vector sends updates containing the state of its own links to all routers in the internetwork.
You type debug ip rip on your router console and see that 172.16.10.0 is being advertised to you with a metric of 16. What does this mean?
What does RIPv2 use to prevent routing loops? CIDR Split horizon Authentication Classless masking Holddown timers
IGRP uses which of the following as default parameters for finding the best path to a remote network? Hop count MTU Cumulative interface delay STP Path bandwidth value
Which command displays RIP routing updates?
Which statement is true regarding classless routing protocols? The use of discontiguous networks is not allowed. The use of variable length subnet masks is permitted. RIPv1 is a classless routing protocol. IGRP supports classless routing within the same autonomous system. RIPv2 supports classless routing.
The Corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. Looking at the output from the Corporate router, what will the router do with this packet? Corp#sh ip route [output cut] R 192.168.215.0 [120/2] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.115.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 R 192.168.30.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0 C 192.168.20.0 is directly connected, Serial0/0 C 192.168.214.0 is directly connected, FastEthernet0/0
Which of the following statements are true regarding the command ip route 172.16.4.0 255.255.255.0 192.168.4.2? The command is used to establish a static route. The default administrative distance is used. The command is used to configure the default route. The subnet mask for the source address is 255.255.255.0.

Discussion & Comments

No comments yet. Be the first to comment!

Join Discussion