Discussion
Home ‣ Chemical Engineering ‣ Process Equipment and Plant Design Comments
- Question
With increase in the reflux ratio for a fixed production from a continuous binary distillation column, the __________ decreases.
Options- A. fixed charges initially
- B. running cost of cooling water for condenser
- C. vapour & liquid load both
- D. running cost of steam for reboiler
- Correct Answer
- fixed charges initially
- 1. LMTD correction factor is used in heat exchanger design for
Options- A. double pipe heat exchanger.
- B. multipass shell and tube heat exchanger.
- C. fouling fluids.
- D. counter flow of hot and cold fluids. Discuss
- 2. A head comprises of straight flange section, corner torus, section and central dished section. Crown radius and knuckle radius in a head is related respectively to the
Options- A. central dished section and corner torus section.
- B. corner torus section and central dished section.
- C. central dished section and straight flange section.
- D. straight flange section and corner torus section. Discuss
- 3. Generally, elliptical dished heads
Options- A. are manufactured on 2:1 ratio of major to minor axis and is recommended to be used for pressure vessels operating above a pressure of 1.5 MN/m2 .
- B. resist half the pressure rating compared to hemi spherical head provided on the cylindrical shell of the same thickness and diameter.
- C. are approximately as strong as seamless cylindrical shell having the corresponding I.D and O.D.
- D. all (a), (b) and (c) Discuss
- 4. Ponchon Savarit method is based on the use of enthalpy concentration diagram, which contains the bubble point curve (saturated liquid curve), dew point curve (saturated vapour curve) and equilibrium tie lines. As compared to McCabe-Thiele's method, this method
Options- A. is more accurate in finding the number of equilibrium stages.
- B. accounts for the enthalpy changes in the process.
- C. facilitates direct calculation of heat load on reboiler & condenser from, the diagram used in this method.
- D. all 'a', 'b' & 'c'. Discuss
- 5.
for fully open gate valves would be
Options- A. much more than that for fully open globe valves.
- B. much less (say 2% than that for fully open globe valves).
- C. around 7.
- D. both (b) and (c). Discuss
- 6. The slope of operating line in the rectifying section of a distillation column is unity, if the reflux ratio is
Options- A. 0
- B. ?
- C. 1
- D. minimum Discuss
- 7. Vertical vessels are not supported by
Options- A. brackets
- B. skirts
- C. columns
- D. saddles Discuss
- 8. Minimum recommended baffle spacing in a shell and tube heat exchanger is about (where, D = shell diameter )
Options- A. 0.2 D
- B. 0.5 D
- C. 0.66 D
- D. 0.80 D Discuss
- 9. Thickness of the frame of a plate and frame filter as compared to that of plates is
Options- A. less
- B. same
- C. more
- D. either (a) or (b) Discuss
- 10. In a __________ rivetted joint, the rivets in the various rows are opposite to each other.
Options- A. zig-zag
- B. chain
- C. diamond
- D. none of these Discuss
Process Equipment and Plant Design problems
Search Results
Correct Answer: multipass shell and tube heat exchanger.
Correct Answer: central dished section and corner torus section.
Correct Answer: all (a), (b) and (c)
Correct Answer: all 'a', 'b' & 'c'.
Correct Answer: both (b) and (c).
Correct Answer: ?
Correct Answer: saddles
Correct Answer: 0.2 D
Correct Answer: more
Correct Answer: chain
Comments
There are no comments.More in Chemical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.