Discussion
Home ‣ Civil Engineering ‣ GATE Exam Questions Comments
- Question
The stepped cantilever is subjected to moments, M as shown in the figure below. The vertical deflection at the free end (neglecting the self weight) is
Options- A.
- B.
- C.
- D. Zero
- Correct Answer
-
- 1. If the shear force at a section of beam under bending is equal to zero then the bending moment at the section is
Options- A. zero
- B. maximum
- C. minimum
- D. minimum or maximum Discuss
- 2. The maximum permissible deflection for a gantry girder, spanning over 6 m, on which an EOT (electric overhead travelling) crane of capacity 200 kN is operating, is
Options- A. 8 mm
- B. 10 mm
- C. 12 mm
- D. 18 mm Discuss
- 3. Use of coagulants such as alum
Options- A. results in reduction of pH of the treated water.
- B. results in increase of pH of the treated water.
- C. results in no chnage in pH of the treated water.
- D. may cause an increase in decrease of decrease of pH of the treated water. Discuss
- 4. In network of pipes
Options- A. the algebraic sum of discharges around each circuit is zero
- B. the algebraic sum of (pressure + datum) head drops around each circuit is zero
- C. the elevation of hydraulic grade line is assumed for each junction point
- D. elementary circuits are replaced by equivalent pipes Discuss
- 5. It is proposed to widen and strengthen an existing 2-lane NH section as a divided highway. The existing traffic in one direction is 2500 commercial vehicles (CV) per day. The construction will take 1 year. The design CBR of soil subgrade is found to be 5 percent, Given: traffic growth rate for CV = 8 percent, vehicle damage factor = 3.5 (standard axles per CV), design life = 10 years and traffic distribution factor = 0.75. The cumulative standard axles (msa) computed are
Options- A. 35
- B. 37
- C. 65
- D. 70 Discuss
- 6. A footing 2 m x 1 m exerts a uniform pressure of 150 kN/m2 on the soil. Assuming a load dispersion of 2 vertical to 1 horizontal the average vertical stress (kN/m2) at 1.0 m below the footing is
Options- A. 50
- B. 75
- C. 80
- D. 100 Discuss
- 7. Bituminous materials are commonly use in highway construction because of their good
Options- A. tensile and compression properties.
- B. binding and water proofing properties.
- C. shear strength and tensile properties.
- D. bond and tensile properties. Discuss
- 8. A road is provided with a horizontal circular curve having deflection angle of 55° and centre line radius of 250 m. A transition curve is to be provided at each end of the circular curve of such a length that the rate of gain of radial acceleration is 0.3 m/s3 at a speed of 50 km per hour. Length of the transition curve required at each of the ends is
Options- A. 2.57 m
- B. 33.33 m
- C. 35.73 m
- D. 1666.67 m Discuss
- 9. Group symbols assigned to silty sand and clayey sand are respectively
Options- A. SS and CS
- B. SM and CS
- C. SM and SC
- D. MS and CS Discuss
- 10. A hyetograph is a graph representing
Options- A. rainfall volume with time
- B. rainfall intensity with time
- C. rainfall intensity with duration
- D. rainfall intensity over an area Discuss
GATE Exam Questions problems
Search Results
Correct Answer: maximum
Correct Answer: 8 mm
Correct Answer: results in reduction of pH of the treated water.
Correct Answer: the algebraic sum of (pressure + datum) head drops around each circuit is zero
Correct Answer: 37
Correct Answer: 50
Correct Answer: binding and water proofing properties.
Correct Answer: 35.73 m
Correct Answer: SM and SC
Correct Answer: rainfall intensity with time
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.