Discussion
Home ‣ Civil Engineering ‣ GATE Exam Questions Comments
- Question
M - ? relationship for a simply supported beam shown below is given by :
Options- A. M l/EI = 2?
- B. M l/EI = 3?
- C. M l/EI = 4?
- D. M l/EI = 6?
- Correct Answer
- M l/EI = 4?
- 1. A soil having particles of nearly the same size is known as
Options- A. well graded
- B. uniformly graded
- C. poorly graded
- D. gap graded Discuss
- 2. The minimum dissolved oxygen content (ppm) in a river necessary for the survival of aquatic life is
Options- A. 0
- B. 2
- C. 4
- D. 8 Discuss
- 3. Consistency Index for a clayer soil is [LL = Liquid Limit, PL = Plastic Limit, PI = Plas-ticity Index, W - natural moisture content]
Options- A.
- B.
- C. LL - PL
- D. 0.5 w Discuss
- 4. Two steel plates each of width 150 mm and thickness 10 mm are connected with three 20 mm diameter rivets placed in a zig-zag pattern. The pitch of the rivets is 75 mm and gauge is 60 mm. If the allowable tensile stress is 150 MPa, the maximum tensile force that the joint can withstand is
Options- A. 195.66 kN
- B. 195.00 kN
- C. 192.75 kN
- D. 225.00 kN Discuss
- 5. The number of revolutions of a current meter in 50 seconds were found to be 12 and 30 corresponding to the velocities of 0.25 and 0.46 m/s respectively. What velocity (in m/s) would be indicated by 50 revolutions of that current meter in one minute?
Options- A. 0.42
- B. 0.50
- C. 0.60
- D. 0.73 Discuss
- 6. The maximum shear stress in a solid shaft of circular cross-section having diameter d subjected to a torque T is ?. If the torque is increased by four times and the diameter of the shaft is increased by two times, the maximum shear stress in the shaft will be
Options- A. 2?
- B. ?
- C. ?/2
- D. ?/4 Discuss
- 7. The values of liquid limit and plasticity index for soils having common geological origin in a rectricted locality usually define
Options- A. A zone above A-line
- B. A straight line parallel to A-line
- C. A straight line perpendicular to A-line
- D. Points may be anywhere in the plasticity chart Discuss
- 8. A trickling filter is primarily a :
Options- A. straining process to remove suspended solids from sewage
- B. biological oxidation process to remove BOD from sewage
- C. straining process to remove turbidity from water
- D. straining process to remove bacteria from water Discuss
- 9. Critical factors for the activated sludge treatment process are
Options- A. maximum hourly flow rate.
- B. maximum and minimum flow rate.
- C. maximum hourly flow rate and maximum daily organic load.
- D. minimum hourly flow rate and minimum daily organic load. Discuss
- 10. Maximum strain at the level of compression steel for a rectangular section having effective cover to compression steel as d' and neutral axis depth from compression face as xu is
Options- A. 0.0035 (1 - d'/xu)
- B. 0.002 (1 - d'/xu)
- C. 0.0035 (1 - xu/d')
- D. 0.002 (1 - xu/d') Discuss
GATE Exam Questions problems
Search Results
Correct Answer: uniformly graded
Correct Answer: 4
Correct Answer:
Correct Answer: 192.75 kN
Correct Answer: 0.60
Correct Answer: ?/2
Correct Answer: A straight line parallel to A-line
Correct Answer: biological oxidation process to remove BOD from sewage
Correct Answer: maximum hourly flow rate and maximum daily organic load.
Correct Answer: 0.0035 (1 - d'/xu)
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.