logo

CuriousTab

CuriousTab

Discussion

Home ‣ Civil Engineering ‣ Steel Structure Design Comments
  • Question

  • A column is carrying an axial load W and an eccentric load P. If A is its cross-sectional area, ex and ey are the eccentricities and Pxx and Zyy the section modulli, the equivalent axial load is obtained from the formula,


  • Options
  • A. A column is carrying an axial load W and an eccentric load P. If A is its cross-sectional area, ex a
  • B. A column is carrying an axial load W and an eccentric load P. If A is its cross-sectional area, ex a
  • C. A column is carrying an axial load W and an eccentric load P. If A is its cross-sectional area, ex a
  • D. A column is carrying an axial load W and an eccentric load P. If A is its cross-sectional area, ex a
  • E.

  • Correct Answer
  •  

    • Steel Structure Design problems

    Search Results

    • 1. For a single section used as a tension member, the given area is assumed

    • Options
    • A. 20% to 30% in excess of the net area
    • B. 30% to 40% in excess of the net area
    • C. 40% to 50% in excess of the net area
    • D. 50% to 60% in excess of the net area
    • E. 60% to 70% in excess of the net area.
      • Discuss
    • 2. Rise of a Jack arch is kept about

    • Options
    • A. 1/2 to 1/3 of the span
    • B. 1/3 to 1/4 of the span
    • C. 1/4 to 1/8 of the span
    • D. 1/8 to 1/12 of the span.
      • Discuss
    • 3. With usual notations of the letters, the shear stress fs at any point of the cross-section is given by

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 4. Tacking rivets in tension members, are provided at a pitch in line not exceeding

    • Options
    • A. 25 cm
    • B. 50 cm
    • C. 75 cm
    • D. 100 cm
      • Discuss
    • 5. Under a concentrated load, bearing stress fb in a beam, is given by (where b is the length of the bearing plate and h is the depth of the root of the fillet).

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 6. The least permissible clear dimension of the web of thickness t in the panel of a plate girder, is restricted to

    • Options
    • A. 150 t
    • B. 160 t
    • C. 170 t
    • D. 180 t
    • E. 200 t
      • Discuss
    • 7. In a grillage footing, the maximum shear force occurs at the

    • Options
    • A. edge of grillage beam
    • B. edge of base plate
    • C. centre of grillage beam
    • D. centre of base plate.
      • Discuss
    • 8. If d is the diameter of column, D is the side of square base, W is total axial load and p is the allowable bending stress, the thickness (t) of the base plate, is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 9. Pick up the correct statement from the following:

    • Options
    • A. The ends of a strut, are connected together with two rivets
    • B. The members of strut will have at least two connections spaced equidistant in their length
    • C. The members when separated back-to-back, the connecting rivets should pass through solid washer or packing
    • D. All the above.
      • Discuss
    • 10. On steel structures the dead load is the weight of

    • Options
    • A. steel work
    • B. material fastened to steel work
    • C. material supported permanently
    • D. all the above.
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.