logo

CuriousTab

CuriousTab

Discussion


Home Networking Managing a Cisco Internetwork See What Others Are Saying!
  • Question
  • The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?


  • Options
  • A. RAM should be erased and the router restarted.
  • B. Flash should be erased and the router restarted.
  • C. NVRAM should be erased and the router restarted.
  • D. The new configuration should be entered and saved.

  • Correct Answer
  • NVRAM should be erased and the router restarted. 

    Explanation
    Before you start to configure the router, you should erase the NVRAM with the erase startup-config command and then reload the router using the reload command.

  • More questions

    • 1. Which command displays RIP routing updates?

    • Options
    • A. show ip route
    • B. debug ip rip
    • C. show protocols
    • D. debug ip route
    • Discuss
    • 2. What is the subnetwork address for a host with the IP address 200.10.5.68/28?

    • Options
    • A. 200.10.5.56
    • B. 200.10.5.32
    • C. 200.10.5.64
    • D. 200.10.5.0
    • Discuss
    • 3. What does a switch do when a frame is received on an interface and the destination hardware address is unknown or not in the filter table?

    • Options
    • A. Forwards the switch to the first available link
    • B. Drops the frame
    • C. Floods the network with the frame looking for the device
    • D. Sends back a message to the originating station asking for a name resolution
    • Discuss
    • 4. Which of the following types of connections can use full duplex?

      1. Hub to hub
      2. Switch to switch
      3. Host to host
      4. Switch to hub
      5. Switch to host

    • Options
    • A. 1, 2 and 4
    • B. 3 and 4
    • C. 3 and 5
    • D. 2, 3 and 5
    • Discuss
    • 5. What is the maximum distance with maximum data rate for 802.11a?

    • Options
    • A. About 65-75 feet
    • B. About 90-100 feet
    • C. About 150 feet
    • D. Over 200 feet
    • Discuss
    • 6. Which command will create a dynamic pool named Todd that will provide you with 30 global addresses?

    • Options
    • A. ip nat pool Todd 171.16.10.65 171.16.10.94 net 255.255.255.240
    • B. ip nat pool Todd 171.16.10.65 171.16.10.94 net 255.255.255.224
    • C. ip nat pool todd 171.16.10.65 171.16.10.94 net 255.255.255.224
    • D. ip nat pool Todd 171.16.10.1 171.16.10.254 net 255.255.255.0
    • Discuss
    • 7. To enable EIGRP, which of the following would you use?

      1. Router1(config-if)# ipv6 ospf 10 area 0.0.0.0
      2. Router1(config-if)# ipv6 router rip 1
      3. Router1(config)# ipv6 router eigrp 10
      4. Router1(config-rtr)# no shutdown
      5. Router1(config-if)# ipv6 eigrp 10

    • Options
    • A. 1, 3 and 5
    • B. 3, 4 and 5
    • C. 1 and 3
    • D. 5 only
    • Discuss
    • 8. Which of the following is true regarding access lists applied to an interface?

    • Options
    • A. You can place as many access lists as you want on any interface until you run out of memory.
    • B. You can apply only one access list on any interface.
    • C. One access list may be configured, per direction, for each layer 3 protocol configured on an interface.
    • D. You can apply two access lists to any interface.
    • Discuss
    • 9. A receiving host has failed to receive all of the segments that it should acknowledge. What can the host do to improve the reliability of this communication session?

    • Options
    • A. Send a different source port number.
    • B. Restart the virtual circuit.
    • C. Decrease the sequence number.
    • D. Decrease the window size.
    • Discuss
    • 10. Which of the following protocols are used to configure trunking on a switch?

      1. VLAN Trunk Protocol
      2. VLAN
      3. 802.1Q
      4. ISL

    • Options
    • A. 1 only
    • B. 3 only
    • C. 3 and 4
    • D. 1, 3 and 4
    • Discuss


    Comments

    There are no comments.

Enter a new Comment