Discussion
Home ‣ Networking ‣ Subnetting See What Others Are Saying!
- Question
What is the maximum number of IP addresses that can be assigned to hosts on a local subnet that uses the 255.255.255.224 subnet mask?
Options- A. 14
- B. 15
- C. 16
- D. 30
- Correct Answer
- 30
ExplanationA /27 (255.255.255.224) is 3 bits on and 5 bits off. This provides 8 subnets, each with 30 hosts. Does it matter if this mask is used with a Class A, B, or C network address? Not at all. The number of host bits would never change. - 1. What two multicast addresses does OSPFv3 use?
- FF02::A
- FF02::9
- FF02::5
- FF02::6
Options- A. 2 only
- B. 3 only
- C. 1 and 3
- D. 3 and 4 Discuss
- 2. Which of the following commands will display the current IP addressing and the layer 1 and 2 status of an interface?
- show version
- show protocols
- show interfaces
- show controllers
- show ip interface
Options- A. 1, 2 and 4
- B. 2, 3 and 5
- C. 3 and 4 only
- D. None of the above Discuss
- 3. What is the frequency range of the IEEE 802.11b standard?
Options- A. 2.4Gbps
- B. 5Gbps
- C. 2.4GHz
- D. 5GHz Discuss
- 4. You are troubleshooting a connectivity problem in your corporate network and want to isolate the problem. You suspect that a router on the route to an unreachable network is at fault. What IOS user exec command should you issue?
Options- A. Router> ping
- B. Router> trace
- C. Router> show ip route
- D. Router> show interface Discuss
- 5. Your switch has a port status LED that is alternating between green and amber. What could this indicate?
Options- A. The port is experiencing errors.
- B. The port is shut down.
- C. The port is in STP blocking mode.
- D. Nothing; this is normal. Discuss
- 6. A network administrator needs to configure a router with a distance-vector protocol that allows classless routing. Which of the following satisfies those requirements?
Options- A. IGRP
- B. OSPF
- C. RIPv1
- D. EIGRP
- E. IS-IS Discuss
- 7. What command is used to stop RIP routing updates from exiting out an interface but still allow the interface to receive RIP route updates?
Options- A. Router(config-if)# no routing
- B. Router(config-if)# passive-interface
- C. Router(config-router)# passive-interface s0
- D. Router(config-router)# no routing updates Discuss
- 8. Which of the following services use TCP?
- DHCP
- SMTP
- HTTP
- TFTP
- FTP
Options- A. 1 and 2
- B. 2, 3 and 5
- C. 1, 2 and 4
- D. 1, 3 and 4 Discuss
- 9. You are unsuccessful in telnetting into a remote device. What could the problem be?
- IP addresses are incorrect.
- Access control list is filtering Telnet.
- There is a defective serial cable.
- The VTY password is missing.
Options- A. 1 only
- B. 3 only
- C. 2 and 4 only
- D. All of the above Discuss
- 10. Acknowledgments, sequencing, and flow control are characteristics of which OSI layer?
Options- A. Layer 2
- B. Layer 3
- C. Layer 4
- D. Layer 7 Discuss
More questions
Correct Answer: 3 and 4
Explanation:
Adjacencies and next-hop attributes now use link-local addresses, and OSPFv3 still uses multicast traffic to send its updates and acknowledgments with the addresses
FF02::5 for OSPF routers and
FF02::6 for OSPF designated routers. These are the replacements for
224.0.0.5 and
224.0.0.6, respectively.
Correct Answer: 2, 3 and 5
Explanation:
The commands
show protocols,
show interfaces, and
show ip interface will show you the layer 1 and 2 status and the IP addresses of your router's interfaces.
Correct Answer: 2.4GHz
Explanation:
The IEEE 802.11b and IEEE 802.11g standards both run in the 2.4GHz RF range.
Correct Answer: Router> trace
Explanation:
The command
traceroute (trace for short), which can be issued from user mode or privileged mode, is used to find the path a packet takes through an internetwork and will also show you where the packet stops because of an error on a router.
Correct Answer: The port is experiencing errors.
Explanation:
When you connect to a switch port, at first the link lights are orange/amber, and then they turn green, indicating normal operation. If the link light is blinking, you have a problem.
Correct Answer: EIGRP
Explanation:
In this question, we're calling EIGRP just plain old distance vector. EIGRP is an "advanced" distance-vector routing protocol, sometimes called a hybrid routing protocol because it uses the characteristics of both distance-vector and link-state routing protocols.
Correct Answer: Router(config-router)# passive-interface s0
Explanation:
The
(config-router)#passive-interface command stops updates from being sent out an interface, but route updates are still received.
Correct Answer: 2, 3 and 5
Explanation:
SMTP, HTTP and FTP use TCP.
Correct Answer: 2 and 4 only
Explanation:
The best answers, the ones you need to remember, are that either an access control list is filtering the Telnet session or the VTY password is not set on the remote device.
Correct Answer: Layer 4
Explanation:
A reliable Transport layer connection uses acknowledgments to make sure all data is transmitted and received reliably. A reliable connection is defined by a virtual circuit that uses acknowledgments, sequencing, and flow control, which are characteristics of the Transport layer (layer 4).
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.