CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Interfacing to the Analog World problems
1. A counter-ramp ADC uses a comparator to compare the input voltage with ________.
Options
A. a binary number
B. the output of a counter
C. the output of a DAC
D. a voltage divider network
Show Answer
Scratch Pad
Discuss
Correct Answer: the output of a DAC
2. A counter-ramp ADC stops counting when ________.
Options
A. the input voltage equals the DAC staircase voltage
B. the counter reaches a maximum count
C. the input voltage equals 5 volts
D. the DAC staircase voltage equals 5 volts
Show Answer
Scratch Pad
Discuss
Correct Answer: the input voltage equals the DAC staircase voltage
3. The main advantage of the tracking A/D converter over the stairstep-ramp A/D converter is that ________.
Options
A. it does not require a counter
B. it uses an up/down counter to indicate the polarity of the input voltage
C. it uses an up/down counter to measure both positive and negative voltages
D. it is faster
Show Answer
Scratch Pad
Discuss
Correct Answer: it is faster
4. The circuit shown below is a(n) ________.
Options
A.
R
/2
R
ladder D/A converter
B. four-bit decoder
C. binary-weighted-input DAC
D. four-bit A/D converter
Show Answer
Scratch Pad
Discuss
Correct Answer:
R
/2
R
ladder D/A converter
5. The number of binary bits at the input of a DAC or the output of an ADC is known as ________.
Options
A. accuracy
B. linearity
C. resolution
D. monotonicity
Show Answer
Scratch Pad
Discuss
Correct Answer: resolution
6. The output of the circuit in the given figure (a) at point X on figure (b) will be ________.
Options
A. 1.011 V
B. 2.75 V
C. ?1.011 V
D. ?2.75 V
Show Answer
Scratch Pad
Discuss
Correct Answer: ?2.75 V
7. ________ ADCs have a fixed value of conversion time that is not dependent on the value of the analog input.
Options
A. Substandard
B. Dual
C. Recessive-approximation
D. Successive-approximation
Show Answer
Scratch Pad
Discuss
Correct Answer: Successive-approximation
8. A signal ________ is produced by sampling the signal at a rate less than the minimum rate identified by Nyquist.
Options
A. Nyquist
B. sampling frequency
C. basis
D. alias
Show Answer
Scratch Pad
Discuss
Correct Answer: alias
9. The fastest analog-to-digital converter is the ________.
Options
A. counter ADC
B. successive-approximation ADC
C. dual slope ADC
D. parallel ADC
Show Answer
Scratch Pad
Discuss
Correct Answer: parallel ADC
10. A binary-weighter resistor DAC is practical only up to a resolution of ________.
Options
A. 10 bits
B. 2 bits
C. 8 bits
D. 4 bits
Show Answer
Scratch Pad
Discuss
Correct Answer: 4 bits
First
13
Last
More in Digital Electronics:
Boolean Algebra and Logic Simplification
Code Converters and Multiplexers
Combinational Logic Analysis
Combinational Logic Circuits
Computers
Counters
Describing Logic Circuits
Digital Arithmetic Operations and Circuits
Digital Concepts
Digital Design
Digital Signal Processing
Digital System Projects Using HDL
Ex-OR and Ex-NOR Gates
Flip-Flops
Integrated-Circuit Logic Families
Integrated Circuit Technologies
Interfacing to the Analog World
Logic Families and Their Characteristics
Logic Gates
Memory and Storage
Microprocessor Fundamentals
MSI Logic Circuits
Multivibrators and 555 Timer
Number Systems and Codes
Programmable Logic Device
Shift Registers
Signals and Switches
The 8051 Microcontroller