logo

CuriousTab

CuriousTab

Discussion


Home Civil Engineering Strength of Materials Comments

  • Question
  • In the given below figure, the rivets with maximum stress, are :
    In the given below figure, the rivets with maximum stress, are : 1 and 2 1 and 3 3 and 4 2 and 4


  • Options
  • A. 1 and 2
  • B. 1 and 3
  • C. 3 and 4
  • D. 2 and 4

  • Correct Answer
  • 2 and 4 


  • Strength of Materials problems


    Search Results


    • 1. Euler's formula states that the buckling load P for a column of length l, both ends hinged and whose least moment of inertia and modulus of elasticity of the material of the column are I and E respectively, is given by the relation

    • Options
    • A.
    • B.
    • C.
    • D.
    • E. P = ?El2.
    • Discuss
    • 2. Maximum deflection of a cantilever due to pure bending moment M at its free end, is

    • Options
    • A.
    • B.
    • C.
    • D.
    • E.
    • Discuss
    • 3. A simply supported beam carries two equal concentrated loads W at distances L/3 from either support. The maximum bending moment

    • Options
    • A.
    • B.
    • C.
    • D.
    • E.
    • Discuss
    • 4. The stress in the wall of a cylinder in a direction normal to its longitudinal axis, due to a force acting along the circumference, is known as

    • Options
    • A. yield stress
    • B. longitudinal stress
    • C. hoop stress
    • D. circumferential stress
    • E. ultimate stress.
    • Discuss
    • 5. A diagram which shows the variations of the axial load for all sections of the span of a beam, is called

    • Options
    • A. bending moment diagram
    • B. shear force diagram
    • C. thrust diagram
    • D. stress diagram
    • E. none of these.
    • Discuss
    • 6. If a solid shaft is subjected to a torque T at its end such that maximum shear stress does not exceed fz the diameter of the shaft will be

    • Options
    • A.
    • B.
    • C.
    • D. none of these.
    • Discuss
    • 7. In a square beam loaded longitudinally, shear develops

    • Options
    • A. on middle fibre along horizontal plane
    • B. on lower fibre along horizontal plane
    • C. on top fibre along vertical plane
    • D. equally on each fibre along horizontal plane
    • E. none of these.
    • Discuss
    • 8. A member which is subjected to reversible tensile or compressive stress may fail at a stress lower than the ultimate stress of the material. This property of metal, is called

    • Options
    • A. plasticity of the metal
    • B. elasticity of the metal
    • C. fatigue of the metal
    • D. workability of the metal.
    • Discuss
    • 9. A cantilever carries is uniformly distributed load W over its whole length and a force W acts at its free end upward. The net deflection of the free end will be

    • Options
    • A. zero
    • B. upward
    • C. downward
    • D. none of these.
    • Discuss
    • 10. Pick up the correct statement from the following :

    • Options
    • A. The distance of the eccentric axial load from the C.G. beyond which tension develops, is known as kern distance
    • B. In visco-elastic material, stress-strain relation is dependent on time
    • C. An instropic material has different properties is different directions
    • D. An orthotropic material has different properties in three mutually perpendicular directions
    • E. All the above.
    • Discuss


    Comments

    There are no comments.

Enter a new Comment