Discussion
Home ‣ Civil Engineering ‣ RCC Structures Design Comments
- Question
In a doubly-reinforced beam if c and t are stresses in concrete and tension reinforcement, d is the effective depth and n is depth of critical neutral axis n, the following relationship holds good
Options- A.
- B.
- C.
- D.
- E.
- Correct Answer
-
- 1. Top bars are extended to the projecting parts of the combined footing of two columns L distance apart for a distance of
Options- A. 0.1 L from the outer edge of column
- B. 0.1 L from the centre edge of column
- C. half the distance of projection
- D. one-fourth the distance of projection. Discuss
- 2. If At is the gross area of steel in tension, d is the effective depth of the beam and y is the depth of the centre of gravity of the resultant compression, the moment of resistance M of the beam, is given by
Options- A. M = At(d - y)
- B. M = Atf(d - y)
- C. M = Atf(d + y)
- D. M =
- E. none of these. Discuss
- 3. An R.C.C. roof slab is designed as a two way slab if
Options- A. it supports live loads in both directions
- B. the ratio of spans in two directions is less than 2
- C. the slab is continuous over two supports
- D. the slab is discontinuous at edges. Discuss
- 4. A foundation is called shallow if its depth, is
Options- A. one-fourth of its width
- B. half of its width
- C. three-fourth of its width
- D. equal to its width
- E. all the above. Discuss
- 5. The angle of internal friction of soil mass is the angle whose
Options- A. tangent is equal to the rate of the maximum resistance to sliding on any internal inclined plane to the normal pressure acting on the plane
- B. sine is equal to the ratio of the maximum resistance to sliding on any internal inclined plane to the normal pressure acting on the plane
- C. cosine is equal to the ratio of the maximum resistance sliding on any internal inclined plane to the normal pressure acting on the plane
- D. none of these. Discuss
- 6. If the size of a column is reduced above the floor, the main bars of the columns, are
Options- A. continued up
- B. bent inward at the floor level
- C. stopped just below the floor level and separate lap bars provided
- D. all the above. Discuss
- 7. A part of the slab may be considered as the flange of the T-beam if
Options- A. flange has adequate reinforcement transverse to beam
- B. it is built integrally with the beam
- C. it is effectively bonded together with the beam
- D. all the above. Discuss
- 8. Design of R.C.C. cantilever beams, is based on the resultant force at
Options- A. fixed end
- B. free end
- C. mid span
- D. mid span and fixed support. Discuss
- 9. Piles are usually driven by
Options- A. diesel operated hammer
- B. drop hammer
- C. single acting steam hammer
- D. all the above. Discuss
- 10. The length of the lap in a compression member is kept greater than bar diameter x (Permissible stress in bar / Five times the bond stress) or
Options- A. 12 bar diameters
- B. 18 bar diameters
- C. 24 bar diameters
- D. 30 bar diameters
- E. 36 bar diameters Discuss
RCC Structures Design problems
Search Results
Correct Answer: 0.1 L from the centre edge of column
Correct Answer: M = Atf(d + y)
Correct Answer: the ratio of spans in two directions is less than 2
Correct Answer: equal to its width
Correct Answer: tangent is equal to the rate of the maximum resistance to sliding on any internal inclined plane to the normal pressure acting on the plane
Correct Answer: all the above.
Correct Answer: all the above.
Correct Answer: fixed end
Correct Answer: all the above.
Correct Answer: 24 bar diameters
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.