logo

CuriousTab

CuriousTab

Discussion

Home ‣ Digital Electronics ‣ Flip-Flops Comments
  • Question

  • An RC circuit used in a 74122 retriggerable one-shot has an REXT of 100 kΩ and a CEXT of 0.005 µF. The pulse width is ________.


  • Options
  • A. 70 µs
  • B. 16 µs
  • C. 160 µs
  • D. 32 µs

  • Correct Answer
  • 160 µs 

    • Flip-Flops problems

    Search Results

    • 1. The circuit given below fails to function; the inputs are checked with a logic probe and the following indications are obtained: CLK, J1, J2, J3, K1, K2, and K3 are pulsing. Q and are HIGH. and PRE are LOW. What could be causing the problem?


    • Options
    • A. There is no problem.
    • B. The clock should be held HIGH.
    • C. The PRE is stuck LOW.
    • D. The CLR is stuck HIGH.
      • Discuss
    • 2. Why are the S and R inputs of a gated flip-flop said to be synchronous?

    • Options
    • A. They must occur with the gate.
    • B. They occur independent of the gate.
      • Discuss
    • 3. On a master-slave flip-flop, when is the master enabled?

    • Options
    • A. when the gate is LOW
    • B. when the gate is HIGH
    • C. both of the above
    • D. neither of the above
      • Discuss
    • 4. How can the cross-coupled NAND flip-flop be made to have active-HIGH S-R inputs?

    • Options
    • A. It can't be done.
    • B. Invert the Q outputs.
    • C. Invert the S-R inputs.
      • Discuss
    • 5. A J-K flip-flop is in a "no change" condition when ________.

    • Options
    • A. J = 1, K = 1
    • B. J = 1, K = 0
    • C. J = 0, K = 1
    • D. J = 0, K = 0
      • Discuss
    • 6. In VHDL, how is each instance of a component addressed?

    • Options
    • A. A name followed by a colon and the name of the library primitive
    • B. A name followed by a semicolon and the component type
    • C. A name followed by the library being used
    • D. A name followed by the component library number
      • Discuss
    • 7. What is the hold condition of a flip-flop?

    • Options
    • A. both S and R inputs activated
    • B. no active S or R input
    • C. only S is active
    • D. only R is active
      • Discuss
    • 8. An RC circuit used in a nonretriggerable 74121 one-shot has an REXT of 49 kΩ and a CEXT of 0.2 µF. The pulse width (tW) is approximately ________.

    • Options
    • A. 6.9 µs
    • B. 6.9 ms
    • C. 69 ms
    • D. 690 ms
      • Discuss
    • 9. In a 555 timer, three 5 kΩ resistors provide a trigger level of ________.

    • Options
    • A. 1/4 VCC and a threshold level 1/2 VCC
    • B. 1/3 VCC and a threshold level 3/4 VCC
    • C. 1/3 VCC and a threshold level 2/3 VCC
    • D. 1/4 VCC and a threshold level 2/3 VCC
      • Discuss
    • 10. Does the cross-coupled NOR flip-flop have active-HIGH or active-LOW set and reset inputs?

    • Options
    • A. active-HIGH
    • B. active-LOW
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.