Discussion
Home ‣ Digital Electronics ‣ Shift Registers Comments
- Question
If an 8-bit ring counter has an initial state 10111110, what is the state after the fourth clock pulse?
Options- A. 11101011
- B. 00010111
- C. 11110000
- D. 00000000
- Correct Answer
- 11101011
- 1. What does the output enable do on the 74395A chip?
Options- A. It determines when data can be loaded.
- B. It forces all outputs to go HIGH.
- C. It forces all outputs to go LOW.
- D. It activates the three-state buffer. Discuss
- 2. With a 200 kHz clock frequency, eight bits can be serially entered into a shift register in ________.
Options- A. 4 ?s
- B. 40 ?s
- C. 400 ?s
- D. 40 ms Discuss
- 3. What is meant by parallel load of a shift register?
Options- A. All FFs are preset with data.
- B. Each FF is loaded with data, one at a time. Discuss
- 4. The group of bits 10110111 is serially shifted (right-most bit first) into an 8-bit parallel output shift register with an initial state 11110000. After two clock pulses, the register contains ________.
Options- A. 10111000
- B. 10110111
- C. 11110000
- D. 11111100 Discuss
- 5. On the third clock pulse, a 4-bit Johnson sequence is Q0 = 1, Q1 = 1, Q2 = 1, and Q3 = 0. On the fourth clock pulse, the sequence is ________.
Options- A. Q0 = 1, Q1 = 1, Q2 = 1, Q3 = 1
- B. Q0 = 1, Q1 = 1, Q2 = 0, Q3 = 0
- C. Q0 = 1, Q1 = 0, Q2 = 0, Q3 = 0
- D. Q0 = 0, Q1 = 0, Q2 = 0, Q3 = 0 Discuss
- 6. What is a transceiver circuit?
Options- A. a buffer that transfers data from input to output
- B. a buffer that transfers data from output to input
- C. a buffer that can operate in both directions Discuss
- 7. In a parallel in/parallel out shift register, D0 = 1, D1 = 1, D2 = 1, and D3 = 0. After three clock pulses, the data outputs are ________.
Options- A. 1110
- B. 0001
- C. 1100
- D. 1000 Discuss
- 8. An 8-bit serial in/serial out shift register is used with a clock frequency of 150 kHz. What is the time delay between the serial input and the Q3 output?
Options- A. 1.67 µs
- B. 26.67 µs
- C. 26.7 ms
- D. 267 ms Discuss
- 9. A sequence of equally spaced timing pulses may be easily generated by which type of counter circuit?
Options- A. ring shift
- B. clock
- C. Johnson
- D. binary Discuss
- 10. When an 8-bit serial in/serial out shift register is used for a 20 µs time delay, the clock frequency is ________.
Options- A. 40 kHz
- B. 50 kHz
- C. 400 kHz
- D. 500 kHz Discuss
Shift Registers problems
Search Results
Correct Answer: It activates the three-state buffer.
Correct Answer: 40 ?s
Correct Answer: All FFs are preset with data.
Correct Answer: 11111100
Correct Answer: Q0 = 1, Q1 = 1, Q2 = 1, Q3 = 1
Correct Answer: a buffer that can operate in both directions
Correct Answer: 0001
Correct Answer: 26.67 µs
Correct Answer: ring shift
Correct Answer: 400 kHz
Comments
There are no comments.More in Digital Electronics:
Programming
Copyright ©CuriousTab. All rights reserved.