Discussion
Home ‣ Networking ‣ Security See What Others Are Saying!
- Question
Which of the following is an example of a standard IP access list?
Options- A. access-list 110 permit host 1.1.1.1
- B. access-list 1 deny 172.16.10.1 0.0.0.0
- C. access-list 1 permit 172.16.10.1 255.255.0.0
- D. access-list standard 1.1.1.1
- Correct Answer
- access-list 1 deny 172.16.10.1 0.0.0.0
ExplanationStandard IP access lists use the numbers 1-99 and 1300-1999 and filter based on source IP address only. Option C is incorrect because the mask must be in wildcard format. - 1. Which of the following is an IEEE standard for frame tagging?
Options- A. ISL
- B. 802.3Z
- C. 802.1Q
- D. 802.3U Discuss
- 2. Which command will display all the EIGRP feasible successor routes known to a router?
Options- A. show ip routes *
- B. show ip eigrp summary
- C. show ip eigrp topology
- D. show ip eigrp adjacencies Discuss
- 3. Which of the following encapsulates PPP frames in Ethernet frames and uses common PPP features like authentication, encryption, and compression?
Options- A. PPP
- B. PPPoA
- C. PPPoE
- D. Token Ring Discuss
- 4. What flavor of Network Address Translation can be used to have one IP address allow many users to connect to the global Internet?
Options- A. NAT
- B. Static
- C. Dynamic
- D. PAT Discuss
- 5. What is the frequency range of the IEEE 802.11g standard?
Options- A. 2.4Gbps
- B. 5Gbps
- C. 2.4GHz
- D. 5GHz Discuss
- 6. Which class of IP address has the most host addresses available by default?
Options- A. A
- B. B
- C. C
- D. A and B Discuss
- 7. How many non-overlapping channels are available with 802.11a?
Options- A. 3
- B. 12
- C. 23
- D. 40 Discuss
- 8. You have the following routing table. Which of the following networks will not be placed in the neighbor routing table?
R 192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 C 192.168.40.0/24 is directly connected, Serial0 172.16.0.0/24 is subnetted, 1 subnets C 172.16.30.0 is directly connected, Loopback0 R 192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0 R 10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0 C 192.168.50.0/24 is directly connected, Ethernet0
Options- A. 172.16.30.0
- B. 192.168.30.0
- C. 10.0.0.0
- D. All of them will be placed in the neighbor routing table. Discuss
- 9. You have created a named access list called Blocksales. Which of the following is a valid command for applying this to packets trying to enter interface s0 of your router?
Options- A. (config)# ip access-group 110 in
- B. (config-if)# ip access-group 110 in
- C. (config-if)# ip access-group Blocksales in
- D. (config-if)# blocksales ip access-list in Discuss
- 10. What multicast addresses does RIPng use?
Options- A. FF02::A
- B. FF02::9
- C. FF02::5
- D. FF02::6 Discuss
More questions
Correct Answer: 802.1Q
Explanation:
802.1Q was created to allow trunked links between disparate switches.
Correct Answer: show ip eigrp topology
Explanation:
Any secondary route to a remote network is considered a feasible successor, and those routes are only found in the topology table and used as backup routes in case of primary route failure. You can see the topology table with the
show ip eigrp topology command.
Correct Answer: PPPoE
Explanation:
PPPoE encapsulates PPP frames in Ethernet frames and uses common PPP features like authentication, encryption, and compression. PPPoA is used for ATM.
Correct Answer: PAT
Explanation:
Port Address Translation (PAT) allows a one-to-many approach to network address translation.
Correct Answer: 2.4GHz
Explanation:
The IEEE 802.11b and IEEE 802.11g standards both run in the 2.4GHz RF range.
Correct Answer: A
Explanation:
Class A addressing provides 24 bits for host addressing.
Correct Answer: 12
Explanation:
The IEEE 802.11a standard provides up to 12 non-overlapping channels.
Correct Answer: 10.0.0.0
Explanation:
The network 10.0.0.0 cannot be placed in the next router's routing table because it already is at 15 hops. One more hop would make the route 16 hops, and that is not valid in RIP networking.
Correct Answer: (config-if)# ip access-group Blocksales in
Explanation:
Using a named access list just replaces the number used when applying the list to the router's interface.
ip access-group Blocksales in is correct.
Correct Answer: FF02::9
Explanation:
RIPng uses the multicast IPv6 address of
FF02::9. If you remember the multicast addresses for IPv4, the numbers at the end of each IPv6 address are the same.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.