Discussion
Home ‣ Networking ‣ IP Routing See What Others Are Saying!
- Question
Two connected routers are configured with RIP routing. What will be the result when a router receives a routing update that contains a higher-cost path to a network already in its routing table?
Options- A. The updated information will be added to the existing routing table.
- B. The update will be ignored and no further action will occur.
- C. The updated information will replace the existing routing table entry.
- D. The existing routing table entry will be deleted from the routing table and all routers will exchange routing updates to reach convergence.
- Correct Answer
- The update will be ignored and no further action will occur.
ExplanationWhen a routing update is received by a router, the router first checks the administrative distance (AD) and always chooses the route with the lowest AD. However, if two routes are received and they both have the same AD, then the router will choose the one route with the lowest metrics, or in RIP's case, hop count. - 1. What is the frequency range of the IEEE 802.11a standard?
Options- A. 2.4Gbps
- B. 5Gbps
- C. 2.4GHz
- D. 5GHz Discuss
- 2. How many non-overlapping channels are available with 802.11b?
Options- A. 3
- B. 12
- C. 23
- D. 40 Discuss
- 3. What is the maximum number of IP addresses that can be assigned to hosts on a local subnet that uses the 255.255.255.224 subnet mask?
Options- A. 14
- B. 15
- C. 16
- D. 30 Discuss
- 4. What are two purposes for segmentation with a bridge?
- To add more broadcast domains.
- To create more collision domains.
- To add more bandwidth for users.
- To allow more broadcasts for users.
Options- A. 1 only
- B. 2 and 3
- C. 2 and 4
- D. 4 only Discuss
- 5. Why does the data communication industry use the layered OSI reference model?
- It divides the network communication process into smaller and simpler components, thus aiding component development, design, and troubleshooting.
- It enables equipment from different vendors to use the same electronic components, thus saving research and development funds.
- It supports the evolution of multiple competing standards and thus provides business opportunities for equipment manufacturers.
- It encourages industry standardization by defining what functions occur at each layer of the model.
Options- A. 1 only
- B. 1 and 4
- C. 2 and 3
- D. 3 only Discuss
- 6. Which of the following allows a router to respond to an ARP request that is intended for a remote host?
Options- A. Gateway DP
- B. Reverse ARP (RARP)
- C. Proxy ARP
- D. Inverse ARP (IARP) Discuss
- 7. Which of the following statements are true regarding the command ip route 172.16.4.0 255.255.255.0 192.168.4.2?
- The command is used to establish a static route.
- The default administrative distance is used.
- The command is used to configure the default route.
- The subnet mask for the source address is 255.255.255.0.
Options- A. 1 and 2
- B. 2 and 4
- C. 3 and 4
- D. All of the above Discuss
- 8. What should the configuration register value be after you successfully complete the password recovery procedure and return the router to normal operation?
Options- A. 0x2100
- B. 0x2101
- C. 0x2102
- D. 0x2142 Discuss
- 9. Which of the following network types have a designated router and a backup designated router assigned?
- Broadcast
- Point-to-point
- NBMA
- NBMA point-to-point
Options- A. 1, 2 and 3
- B. 1 and 3
- C. 3 and 4
- D. All of the above Discuss
- 10. You telnet into a remote device and type debug ip rip, but no output from the debug command is seen. What could the problem be?
Options- A. You must type the show ip rip command first.
- B. IP addressing on the network is incorrect.
- C. You must use the terminal monitor command.
- D. Debug output is sent only to the console. Discuss
More questions
Correct Answer: 5GHz
Explanation:
The IEEE 802.11a standard runs in the 5GHz RF range.
Correct Answer: 3
Explanation:
The IEEE 802.11b standard provides 3 non-overlapping channels.
Correct Answer: 30
Explanation:
A /27 (255.255.255.224) is 3 bits on and 5 bits off. This provides 8 subnets, each with 30 hosts. Does it matter if this mask is used with a Class A, B, or C network address? Not at all. The number of host bits would never change.
Correct Answer: 2 and 3
Explanation:
Bridges break up collision domains, which allow more bandwidth for users.
Correct Answer: 1 and 4
Explanation:
The main advantage of a layered model is that it can allow application developers to change aspects of a program in just one layer of the layer model's specifications.
Advantages of using the OSI layered model include, but are not limited to, the following:
It divides the network communication process into smaller and simpler components, thus aiding compo- nent development, design, and troubleshooting;
it allows multiple-vendor development through standardization of network components;
it encourages industry standardization by defining what functions occur at each layer of the model;
it allows various types of network hardware and software to communicate;
Correct Answer: Proxy ARP
Explanation:
Proxy ARP can help machines on a subnet reach remote subnets without configuring routing or a default gateway.
Correct Answer: 1 and 2
Explanation:
Although answer D almost seems right, it is not; the mask is the mask used on the remote network, not the source network. Since there is no number at the end of the static route, it is using the default administrative distance of 1.
Correct Answer: 0x2102
Explanation:
All Cisco routers have a default configuration register setting of
0x2102, which tells the router to load the IOS from flash memory and the configuration from NVRAM.
Correct Answer: 1 and 3
Explanation:
No DR is assigned on any type of point-to-point link. No DR/BDR is assigned on the NBMA point-to-multipoint due to the hub/spoke topology. DR and BDR are elected on broadcast and non-broadcast multi-access networks. Frame Relay is a non-Broadcast Multi-Access (NBMA) network by default.
Correct Answer: You must use the terminal monitor command.
Explanation:
To see console messages through your Telnet session, you must enter the
terminal monitor command.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.