logo

CuriousTab

CuriousTab

Discussion


Home Networking IP Routing See What Others Are Saying!
  • Question
  • If your routing table has a static, a RIP, and an IGRP route to the same network, which route will be used to route packets by default?


  • Options
  • A. Any available route
  • B. RIP route
  • C. Static route
  • D. IGRP route
  • E. They will all load-balance.

  • Correct Answer
  • Static route 

    Explanation
    Static routes have an administrative distance of 1 by default. Unless you change this, a static route will always be used over any other found route. IGRP has an administrative distance of 100, and RIP has an administrative distance of 120, by default.

  • More questions

    • 1. What flavor of Network Address Translation can be used to have one IP address allow many users to connect to the global Internet?

    • Options
    • A. NAT
    • B. Static
    • C. Dynamic
    • D. PAT
    • Discuss
    • 2. What is the frequency range of the IEEE 802.11g standard?

    • Options
    • A. 2.4Gbps
    • B. 5Gbps
    • C. 2.4GHz
    • D. 5GHz
    • Discuss
    • 3. Which class of IP address has the most host addresses available by default?

    • Options
    • A. A
    • B. B
    • C. C
    • D. A and B
    • Discuss
    • 4. How many non-overlapping channels are available with 802.11a?

    • Options
    • A. 3
    • B. 12
    • C. 23
    • D. 40
    • Discuss
    • 5. You have the following routing table. Which of the following networks will not be placed in the neighbor routing table?
      R    192.168.30.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0
      C    192.168.40.0/24 is directly connected, Serial0
           172.16.0.0/24 is subnetted, 1 subnets
      C    172.16.30.0 is directly connected, Loopback0
      R    192.168.20.0/24 [120/1] via 192.168.40.1, 00:00:12, Serial0
      R    10.0.0.0/8 [120/15] via 192.168.40.1, 00:00:07, Serial0
      C    192.168.50.0/24 is directly connected, Ethernet0

    • Options
    • A. 172.16.30.0
    • B. 192.168.30.0
    • C. 10.0.0.0
    • D. All of them will be placed in the neighbor routing table.
    • Discuss
    • 6. You have created a named access list called Blocksales. Which of the following is a valid command for applying this to packets trying to enter interface s0 of your router?

    • Options
    • A. (config)# ip access-group 110 in
    • B. (config-if)# ip access-group 110 in
    • C. (config-if)# ip access-group Blocksales in
    • D. (config-if)# blocksales ip access-list in
    • Discuss
    • 7. What multicast addresses does RIPng use?

    • Options
    • A. FF02::A
    • B. FF02::9
    • C. FF02::5
    • D. FF02::6
    • Discuss
    • 8. What is the maximum distance running the lowest data rate for 802.11a?

    • Options
    • A. About 100 feet
    • B. About 175 feet
    • C. About 300 feet
    • D. About 350 feet
    • Discuss
    • 9. Which of the following is considered to be the destination host before translation?

    • Options
    • A. Inside local
    • B. Outside local
    • C. Inside global
    • D. Outside global
    • Discuss
    • 10. Which router command allows you to view the entire contents of all access lists?

    • Options
    • A. show all access-lists
    • B. show access-lists
    • C. show ip interface
    • D. show interface
    • Discuss


    Comments

    There are no comments.

Enter a new Comment