Discussion
Home ‣ Networking ‣ Networking Basics Comments
- Question
What does a VLAN do?
Options- A. Acts as the fastest port to all servers.
- B. Provides multiple collision domains on one switch port.
- C. Breaks up broadcast domains in a layer 2 switch internetwork.
- D. Provides multiple broadcast domains within a single collision domain.
- Correct Answer
- Breaks up broadcast domains in a layer 2 switch internetwork.
ExplanationVLANs break up broadcast domains at layer 2. - 1. You have 10 users plugged into a hub running 10Mbps half-duplex. There is a server connected to the switch running 10Mbps half-duplex as well. How much bandwidth does each host have to the server?
Options- A. 100 kbps
- B. 1 Mbps
- C. 2 Mbps
- D. 10 Mbps Discuss
- 2. What is a stub network?
Options- A. A network with more than one exit point.
- B. A network with more than one exit and entry point.
- C. A network with only one entry and no exit point.
- D. A network that has only one entry and exit point. Discuss
- 3. What command will display the line, protocol, DLCI, and LMI information of an interface?
Options- A. sh pvc
- B. show interface
- C. show frame-relay pvc
- D. show run Discuss
- 4. In a network with dozens of switches, how many root bridges would you have?
Options- A. 1
- B. 2
- C. 5
- D. 12 Discuss
- 5. If your router is facilitating a CSU/DSU, which of the following commands do you need to use to provide the router with a 64000bps serial link?
Options- A. RouterA(config)#bandwidth 64
- B. RouterA(config-if)#bandwidth 64000
- C. RouterA(config-if)#clock rate 64
- D. RouterA(config-if)#clock rate 64000 Discuss
- 6. What protocols are used to configure trunking on a switch?
- VLAN Trunking Protocol
- VLAN
- 802.1Q
- ISL
Options- A. 1 and 2
- B. 3 and 4
- C. 1 only
- D. 2 only Discuss
- 7. Which of the following is the valid host range for the subnet on which the IP address 192.168.168.188 255.255.255.192 resides?
Options- A. 192.168.168.129-190
- B. 192.168.168.129-191
- C. 192.168.168.128-190
- D. 192.168.168.128-192 Discuss
- 8. Which protocol is used to send a destination network unknown message back to originating hosts?
Options- A. TCP
- B. ARP
- C. ICMP
- D. BootP Discuss
- 9. What does the passive command provide to dynamic routing protocols?
Options- A. Stops an interface from sending or receiving periodic dynamic updates.
- B. Stops an interface from sending periodic dynamic updates but not from receiving updates.
- C. Stops the router from receiving any dynamic updates.
- D. Stops the router from sending any dynamic updates. Discuss
- 10. Which protocol does DHCP use at the Transport layer?
Options- A. IP
- B. TCP
- C. UDP
- D. ARP Discuss
Networking Basics problems
Search Results
Correct Answer: 10 Mbps
Explanation:
Each device has 10 Mbps to the server.
Correct Answer: A network that has only one entry and exit point.
Explanation:
Stub networks have only one connection to an internetwork. Only default routes can be set on a stub network or network loops may occur.
Correct Answer: show interface
Explanation:
The
show interface command shows the line, protocol, DLCI, and LMI information of an interface.
Correct Answer: 1
Explanation:
You should have only one root bridge per network.
Correct Answer: RouterA(config-if)#clock rate 64000
Explanation:
The
clock rate command is two words, and the speed of the line is in bps.
Correct Answer: 3 and 4
Explanation:
VTP is not right because it has nothing to do with trunking except that it sends VLAN information across a trunk link. 802.1Q and ISL are used to configure trunking on a port.
Correct Answer: 192.168.168.129-190
Explanation:
256 - 192 = 64. 64 + 64 = 128. 128 + 64 = 192. The subnet is 128, the broadcast address is 191, and the valid host range is the numbers in between, or 129-190.
Correct Answer: ICMP
Explanation:
ICMP is the protocol at the Network layer that is used to send messages back to an originating router.
Correct Answer: Stops an interface from sending periodic dynamic updates but not from receiving updates.
Explanation:
The
passive command, short for passive-interface, stops regular updates from being sent out an interface. However, the interface can still receive updates.
Correct Answer: UDP
Explanation:
User Datagram Protocol is a connection network service at the Transport layer, and DHCP uses this connectionless service.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.