Discussion
Home ‣ Civil Engineering ‣ Estimating and Costing Comments
- Question
The most reliable estiamte is
Options- A. Detailed estimate
- B. Preliminary estimate
- C. Plinth area estimate
- D. Cube rate estimate
- E. None of these.
- Correct Answer
- Detailed estimate
- 1. The inspection pit or chamber is a manhole provided in a base drainage system
Options- A. at every change of direction
- B. at every change of gradient
- C. at every 30 m intervals
- D. at the point where vertical soil pipe joins the house drain
- E. All the above. Discuss
- 2. According to ISI method of measurement, the order of the sequence is
Options- A. Length, breadth, height
- B. Breadth, length, height
- C. Height, length, breadth
- D. None of these. Discuss
- 3. In long and short wall method of estimation, the length of long wall is the centre to centre distance between the walls and
Options- A. breadth of the wall
- B. half breadth of wall on each side
- C. one fourth breadth of wall on each side
- D. None of these. Discuss
- 4. Pick up the correct statement from the following:
Options- A. The earth work of cutting in trenches or borrow pits in fairly uniform ground is measured with the help of average depths of the dead men
- B. The earth work in trenches or borrow pits in irregular ground is measured by taking the difference in levels before and after completion of work
- C. The earth work in trenches or borrow pits, where neither a nor b is feasible, are measured from the fillings after deduction of voids
- D. All the above. Discuss
- 5. Pick up the incorrect statement from the following:
Options- A. Dimensions are measured to the nearest 0.01 m
- B. Areas are measured to the nearest 0.01 sq.m
- C. Cubic contents are measured to the nearest 0.1 cm m
- D. Weights are measured to the nearest 0.001 tonnes Discuss
- 6. The measurement is not made in square metres in case of
Options- A. D.P.C. (Damp proof course)
- B. Form works
- C. Concrete Jaffries
- D. R.C. Chhajja. Discuss
- 7. The expected out turn of 12 mm plastering with cement mortar is
Options- A. 2.5 sq m
- B. 4.0 sq m
- C. 6.0 sq m
- D. 8.0 sq m
- E. 10 sq m Discuss
- 8. The area of a sloping surface of a protective embankment of mean height d, side slopes S : 1 and length L is
Options- A. d x d x s
- B. d2 x (ds)2
- C. L.D 1 + s2
- D. 2 LD 1 + s2 Discuss
- 9. Pick up the item of work not included in the plinth area estimate
Options- A. Wall thickness
- B. Room area
- C. Verandah area
- D. W.C. area
- E. Courtyard area. Discuss
- 10. If tensile stress of a steel rod of diameter D is 1400 kg/cm2 and bond stress is 6 kg/cm2, the required bond length of the rod is
Options- A. 30 D
- B. 40 D
- C. 50 D
- D. 53 D
- E. 59 D Discuss
Estimating and Costing problems
Search Results
Correct Answer: All the above.
Correct Answer: Length, breadth, height
Correct Answer: half breadth of wall on each side
Correct Answer: All the above.
Correct Answer: Cubic contents are measured to the nearest 0.1 cm m
Correct Answer: R.C. Chhajja.
Correct Answer: 8.0 sq m
Correct Answer: L.D 1 + s2
Correct Answer: Courtyard area.
Correct Answer: 59 D
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.