Discussion
Home ‣ Civil Engineering ‣ Hydraulics Comments
- Question
Water flows through a convergent mouthpiece of diameter 4 cm at convergence under a head of 3 metres. If the maximum vacuum pressure is 9 metres of water, the maximum diameter of divergence, to aviod separation of flow, is
Options- A. 4 cm
- B. 6 cm
- C. 2 cm
- D. 23 cm.
- Correct Answer
- 2 cm
- 1. Pick up the correct statement from the following :
Options- A. In incompressible flow the density of a fluid remains constant
- B. In compressible flow, the density of a fluid changes from point to point
- C. In uniform flow, the velocity of a fluid does not change with respect to length of flow direction
- D. All the above. Discuss
- 2. If v1 and v2 are the velocities of flow before and after sudden enlargement in a pipe, the head loss given by Carnot and Borda equation, is
Options- A. (v22 - v12)/2g
- B. (v1 - v2)2/2g
- C. (v2 - v1)2/2g
- D. (v1 + v2)2/2g. Discuss
- 3. Pick up the correct statement from the following :
Options- A. For maximum velocity of flow, the depth of water in the circular channel must be 0.81 times the diameter of the channel
- B. For maximum velocity, the hydraulic mean depth must be 0.3 times the diameter of circular channel
- C. For maximum discharge the depth of flow must be 0.95 times the diameter of circular channel
- D. All the above. Discuss
- 4. The differential equation dp/? + gdz + vdv = 0 for a fluid motion is suggested by
Options- A. Bernoulli
- B. Cauchy-Riemann
- C. Laplace
- D. Leonard Euler. Discuss
- 5. An orifice is an opening in a vessel with
Options- A. closed perimeter of regular shape through which water flows
- B. the water level of the liquid on the up stream side is below the top of the orifice
- C. partially full flow
- D. prolonged sides having length of 2 to 3 diameters of the opening in thick wall. Discuss
- 6. A spherical load 900 kg is rolled through 9.8 m across the deck of a ship weighing 10, 000 kg. If the metacentric height of the ship is 5 metres, the angle of heel, is
Options- A. 10° 5'
- B. 10° 10'
- C. 10° 15'
- D. 10° 20' Discuss
- 7. The value of kinetic energy correction factor (a) for a laminar flow through a circular pipe, is
Options- A. 0.5
- B. 1.0
- C. l.5
- D. 2.0
- E. 2.5 Discuss
- 8. If H is height of the liquid above the sill, the effect of end contractions, according to Francis formula, is
Options- A. 0.1 H
- B. 0.2 H
- C. 0.3 H
- D. 0.4 H
- E. 0.5 H. Discuss
- 9. If H is the difference of liquid levels on two sides of an orifice (width b, depth d), the discharge through the orifice will be
Options- A. Cdbd22gH
- B. Cdb2d2gH
- C. Cdbd2gh
- D. Cdbd.2g H1/2. Discuss
- 10. A triangular notch is preferred to a rectangular notch because
Options- A. only one reading is required
- B. its formula is simple to remember
- C. it gives more accurate results for low discharge
- D. it measures a wide range of flows accurately
- E. all the above. Discuss
Hydraulics problems
Search Results
Correct Answer: All the above.
Correct Answer: (v1 - v2)2/2g
Correct Answer: All the above.
Correct Answer: Leonard Euler.
Correct Answer: closed perimeter of regular shape through which water flows
Correct Answer: 10° 15'
Correct Answer: 2.0
Correct Answer: 0.1 H
Correct Answer: Cdbd2gh
Correct Answer: all the above.
Comments
There are no comments.More in Civil Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.