Discussion
Home ‣ Digital Electronics ‣ Flip-Flops Comments
- Question
How many flip-flops are required to produce a divide-by-128 device?
Options- A. 1
- B. 4
- C. 6
- D. 7
- Correct Answer
- 7
- 1. Which statement BEST describes the operation of a negative-edge-triggered D flip-flop?
Options- A. The logic level at the D input is transferred to Q on NGT of CLK.
- B. The Q output is ALWAYS identical to the CLK input if the D input is HIGH.
- C. The Q output is ALWAYS identical to the D input when CLK = PGT.
- D. The Q output is ALWAYS identical to the D input. Discuss
- 2. How is a J-K flip-flop made to toggle?
Options- A. J = 0, K = 0
- B. J = 1, K = 0
- C. J = 0, K = 1
- D. J = 1, K = 1 Discuss
- 3. If both inputs of an S-R flip-flop are low, what will happen when the clock goes HIGH?
Options- A. An invalid state will exist.
- B. No change will occur in the output.
- C. The output will toggle.
- D. The output will reset. Discuss
- 4. What is the significance of the J and K terminals on the J-K flip-flop?
Options- A. There is no known significance in their designations.
- B. The J represents "jump," which is how the Q output reacts whenever the clock goes high and the J input is also HIGH.
- C. The letters were chosen in honor of Jack Kilby, the inventory of the integrated circuit.
- D. All of the other letters of the alphabet are already in use. Discuss
- 5. What is the difference between the enable input of the 7475 and the clock input of the 7474?
Options- A. The 7475 is edge-triggered.
- B. The 7474 is edge-triggered. Discuss
- 6. A positive edge-triggered J-K flip-flop is used to produce a two-phase clock. However, when the circuit is operated it produces erratic results. Close examination with a scope reveals the presence of glitches. What causes the glitches, and how might the problem be corrected?
Options- A. The PRESET and CLEAR terminals may have been left floating; they should be properly terminated if not being used.
- B. The problem is caused by a race condition between the J and K inputs; an inverter should be inserted in one of the terminals to correct the problem.
- C. A race condition exists between the Q and Q outputs to the AND gate; the AND gate should be replaced with a NAND gate.
- D. A race condition exists between the clock and the outputs of the flip-flop feeding the AND gate; replace the flip-flop with a negative edge-triggered J-K Flip-Flop. Discuss
- 7. For an S-R flip-flop to be set or reset, the respective input must be:
Options- A. installed with steering diodes
- B. in parallel with a limiting resistor
- C. LOW
- D. HIGH Discuss
- 8. A 555 operating as a monostable multivibrator has an R1 of 220 kΩ. Determine C1 for a pulse width of 4 ms.
Options- A. 0.017 µF
- B. 17 pF
- C. 170 pF
- D. 1,700 µF Discuss
- 9. Which is not a real advantage of HDL?
Options- A. Using higher levels of abstraction
- B. Tailoring components to exactly fit the needs of the project
- C. The use of graphical tools
- D. Using higher levels of abstraction and tailoring components to exactly fit the needs of the project Discuss
- 10. A gated S-R latch and its associated waveforms are shown below. What, if anything, is wrong and what could be causing the problem?
Options- A. The
output is always low; the circuit is defective. - B. The Q output should be the complement of the
output; the S and R terminals are reversed. - C. The Q should be following the R input; the R input is defective.
- D. There is nothing wrong with the circuit. Discuss
Flip-Flops problems
Search Results
Correct Answer: The logic level at the D input is transferred to Q on NGT of CLK.
Correct Answer: J = 1, K = 1
Correct Answer: No change will occur in the output.
Correct Answer: The letters were chosen in honor of Jack Kilby, the inventory of the integrated circuit.
Correct Answer: The 7474 is edge-triggered.
Correct Answer: A race condition exists between the clock and the outputs of the flip-flop feeding the AND gate; replace the flip-flop with a negative edge-triggered J-K Flip-Flop.
Correct Answer: HIGH
Correct Answer: 0.017 µF
Correct Answer: The use of graphical tools
Correct Answer: The
output is always low; the circuit is defective. Comments
There are no comments.More in Digital Electronics:
Programming
Copyright ©CuriousTab. All rights reserved.