Discussion
Home ‣ Digital Electronics ‣ Digital Design Comments
- Question
How much setup time (ts) is required for the 74LS76?
Options- A. 5 ns
- B. 10 ns
- C. 20 ns
- D. 40 ns
- Correct Answer
- 20 ns
- 1. Can the automatic RC circuit be used to set a flip-flop rather than reset the flip-flop?
Options- A. yes
- B. no Discuss
- 2. Setup time specifies:
Options- A. the minimum time the control levels need to be maintained on the inputs prior to the triggering edge of the clock in order to be reliably clocked into the flip-flop
- B. the maximum time interval required for the control levels to remain on the inputs before the triggered edge of the clock in order for the data to be reliably clocked out of the flip-flop
- C. how long the operator has to get the flip-flop running before the maximum power level is exceeded
- D. how long it takes the output to change states after the clock has transitioned Discuss
- 3. An optocoupler is an integrated circuit with an LED and a zener diode encased in the same package.
Options- A. True
- B. False Discuss
- 4. What would be the output voltage of a 7814 voltage regulator?
Options- A. ?14 V dc
- B. +14 V dc
- C. ?8 V dc
- D. +8 V dc Discuss
- 5. The circuit in Figure 9-8 is defective; data is not appearing on the output lines. A check with the scope shows data pulses on the serial data line and multiplex control lines, S0?S2; no parity error is indicated. A further check with a logic probe indicates that Vcc and ground appear to be present. What might be wrong with the circuit?
Options- A. The demultiplexer may be bad.
- B. The parity checker is defective.
- C. The parity generator may be bad.
- D. The parity checker is defective, or the parity generator may be bad. Discuss
- 6. A 0.01-µF capacitor is recommended by TTL manufacturers for ________ the power supply.
Options- A. decoupling
- B. filtering
- C. rectifying
- D. grounding Discuss
- 7. Why would a delay gate be needed for a digital circuit?
Options- A. A delay gate is never needed.
- B. to provide for setup times
- C. to provide for hold times
- D. to provide for setup times and hold times Discuss
- 8. Why is the Schmitt trigger needed in the 60-Hz TTL-level clock pulse generator?
Options- A. to provide a triangle wave
- B. to provide a sine wave
- C. to provide a rounded pulse waveform
- D. to provide a sharp pulse waveform Discuss
- 9. Look up the propagation delay from the clock to the output for the 7476. Are the HIGH-to-LOW and LOW-to-HIGH propagation delays the same?
Options- A. yes
- B. no, tPLH = 25 ns, tPHL = 40 ns
- C. no, tPLH = 40 ns, tPHL = 25 ns
- D. no, tPHL = 25 ns, tPLH = 40 ns Discuss
- 10. In the automatic reset circuit for a flip-flop, how long does it take the capacitor to completely charge?
Options- A. 1 time constant (RC)
- B. 2 time constants (RC)
- C. 5 time constants (RC)
- D. 10 time constants (RC) Discuss
Digital Design problems
Search Results
Correct Answer: yes
Correct Answer: the minimum time the control levels need to be maintained on the inputs prior to the triggering edge of the clock in order to be reliably clocked into the flip-flop
Correct Answer: False
Correct Answer: +14 V dc
Correct Answer: The demultiplexer may be bad.
Correct Answer: decoupling
Correct Answer: to provide for setup times and hold times
Correct Answer: to provide a sharp pulse waveform
Correct Answer: no, tPLH = 25 ns, tPHL = 40 ns
Correct Answer: 5 time constants (RC)
Comments
There are no comments.More in Digital Electronics:
Programming
Copyright ©CuriousTab. All rights reserved.