Discussion
Home ‣ Digital Electronics ‣ Interfacing to the Analog World Comments
- Question
What is the purpose of a sample-and-hold circuit?
Options- A. To keep temporary memory
- B. To hold a voltage constant so an ADC has time to produce an output
- C. To hold a voltage constant so a DAC has time to produce an output
- D. To hold data after a multiplexer has selected an output
- Correct Answer
- To hold a voltage constant so an ADC has time to produce an output
- 1. The practical use of binary-weighted digital-to-analog converters is limited to:
Options- A. R/2R ladder D/A converters
- B. 4-bit D/A converters
- C. 8-bit D/A converters
- D. op-amp comparators Discuss
- 2. What circuitry is on an ADC0808 IC?
Options- A. A multiplexer
- B. An ADC
- C. A 3-bit select input code
- D. All of the above Discuss
- 3. The main advantage of the successive-approximation A/D converter over the counter-ramp A/D converter is its:
Options- A. more complex circuitry
- B. less complex circuitry
- C. longer conversion time
- D. shorter conversion time Discuss
- 4. Sample-and-hold circuits in A/D converters are designed to:
Options- A. sample and hold the output of the binary counter during the conversion process
- B. stabilize the comparator's threshold voltage during the conversion process
- C. stabilize the input analog signal during the conversion process
- D. sample and hold the D/A converter staircase waveform during the conversion process Discuss
- 5. An actuator is usually a device that:
Options- A. converts analog data to meaningful digital data.
- B. controls a physical variable.
- C. stores digital data and then processes that data according to a set of specified instructions.
- D. converts a physical variable to an electrical variable. Discuss
- 6. Why is a binary-weighted DAC usually limited to 4-bit binary conversion?
Options- A. too many pins on the IC
- B. too many op amps needed
- C. too many different values of capacitors
- D. too many different values of resistors Discuss
- 7. Which of the statements below best describes the basic operation of a dual-slope A/D converter?
Options- A. The input voltage is used to set the frequency of a voltage-controlled oscillator (VCO). The VCO quits changing frequency when the input voltage stabilizes. The frequency of the VCO, which is proportional to the analog input voltage, is measured and is displayed on the digital display as a voltage reading.
- B. A ramp generator is used to enable a counter through a comparator. When the ramp voltage equals the input voltage, the counter is latched and then reset. The counter reading is proportional to the input voltage since the ramp is changing at a constant V/second rate.
- C. A ramp voltage and analog input voltage are applied to a comparator. As the input voltage causes the integrating capacitor to charge, it will at some point equal the ramp voltage. The ramp voltage is measured and displayed on the digital panel meter.
- D. Two ramps are generated: one by the input voltage and the other by a reference voltage. The input voltage ramp charges the integrating capacitor, while the reference voltage discharges the capacitor and enables the counter until the capacitor is discharged, at which time the counter value is loaded into the output latches. Discuss
- 8. What is the maximum conversion time for a counter-ramp ADC with 8-bit resolution and a clock frequency of 20 kHz?
Options- A. 12.8 ms
- B. 6.4 ms
- C. 0.05 ms
- D. 0.4 ms Discuss
- 9. Two principal advantages of the dual-slope ADC are its:
Options- A. high speed and low cost.
- B. high sensitivity to noise and low cost.
- C. low sensitivity to noise and high speed.
- D. low sensitivity to noise and low cost. Discuss
- 10. What is the output voltage of the given circuit if the inputs are as follows:
20 = 1, 21 = 1, 22 = 0, 23 = 0?
Options- A. ?3.115 volts
- B. ?2.8025 volts
- C. ?1.875 volts
- D. ?1.24 volts Discuss
Interfacing to the Analog World problems
Search Results
Correct Answer: 4-bit D/A converters
Correct Answer: All of the above
Correct Answer: shorter conversion time
Correct Answer: stabilize the input analog signal during the conversion process
Correct Answer: controls a physical variable.
Correct Answer: too many different values of resistors
Correct Answer: Two ramps are generated: one by the input voltage and the other by a reference voltage. The input voltage ramp charges the integrating capacitor, while the reference voltage discharges the capacitor and enables the counter until the capacitor is discharged, at which time the counter value is loaded into the output latches.
Correct Answer: 12.8 ms
Correct Answer: low sensitivity to noise and low cost.
Correct Answer: ?1.875 volts
Comments
There are no comments.More in Digital Electronics:
Programming
Copyright ©CuriousTab. All rights reserved.