Discussion
Home ‣ Digital Electronics ‣ Memory and Storage Comments
- Question
What is the difference between static RAM and dynamic RAM?
Options- A. Static RAM must be refreshed, dynamic RAM does not.
- B. There is no difference.
- C. Dynamic RAM must be refreshed, static RAM does not.
- Correct Answer
- Dynamic RAM must be refreshed, static RAM does not.
- 1. Which of the following describes the action of storing a bit of data in a mask ROM?
Options- A. A 1 is stored in a bipolar cell by opening the base connection to the address line.
- B. A 0 is stored in a bipolar cell by shorting the base connection to the address line.
- C. A 1 is stored by connecting the gate of a MOS cell to the address line.
- D. A 0 is stored by connecting the gate of a MOS cell to the address line. Discuss
- 2. What is the significance of the inverted triangles on the outputs of the device in the given figure?
Options- A. They represent inverters and mean that the outputs are active-LOW.
- B. They represent buffers and mean that the outputs can drive 40 TTL loads, instead of the normal 10.
- C. It means that the outputs will be active only if a change has occurred at that memory location since the last read/write cycle.
- D. The outputs are tristated. Discuss
- 3. The ideal memory ________.
Options- A. has high storage capacity
- B. is nonvolatile
- C. has in-system read and write capacity
- D. has all of the above characteristics Discuss
- 4. In general, the ________ have the smallest bit size and the ________ have the largest.
Options- A. EEPROMs, Flash
- B. SRAM, mask ROM
- C. mask ROM, SRAM
- D. DRAM, PROM Discuss
- 5. The main advantage of semiconductor RAM is its ability to:
Options- A. retain stored data when power is interrupted or turned off
- B. be written to and read from rapidly
- C. be randomly accessed
- D. be sequentially accessed Discuss
- 6. An 8-bit address code can select ________.
Options- A. 8 locations in memory
- B. 256 locations in memory
- C. 65,536 locations in memory
- D. 131,072 locations in memory Discuss
- 7. Which type of ROM has to be custom built by the factory?
Options- A. ROM
- B. mask ROM
- C. EPROM
- D. EEPROM Discuss
- 8. Which of the following is one of the basic characteristics of DRAMs?
Options- A. DRAMs must have a constantly changing input.
- B. DRAMs must be periodically refreshed in order to be able to retain data.
- C. DRAMs have a broader "dynamic" storage range than other types of memories.
- D. DRAMs are simpler devices than other types of memories. Discuss
- 9. Why is a refresh cycle necessary for a dynamic RAM?
Options- A. to clear the flip-flops
- B. to set the flip-flops
- C. The refresh cycle discharges the capacitor cells.
- D. The refresh cycle keeps the charge on the capacitor cells. Discuss
- 10. Which of the following is NOT a type of memory?
Options- A. RAM
- B. ROM
- C. FPROM
- D. EEPROM Discuss
Memory and Storage problems
Search Results
Correct Answer: A 1 is stored by connecting the gate of a MOS cell to the address line.
Correct Answer: The outputs are tristated.
Correct Answer: has all of the above characteristics
Correct Answer: EEPROMs, Flash
Correct Answer: be written to and read from rapidly
Correct Answer: 256 locations in memory
Correct Answer: mask ROM
Correct Answer: DRAMs must be periodically refreshed in order to be able to retain data.
Correct Answer: The refresh cycle keeps the charge on the capacitor cells.
Correct Answer: FPROM
Comments
There are no comments.More in Digital Electronics:
Programming
Copyright ©CuriousTab. All rights reserved.