logo

CuriousTab

CuriousTab

Discussion


Home Networking IPv6 See What Others Are Saying!
  • Question
  • Which of the following is true when describing a multicast address?


  • Options
  • A. Packets addressed to a unicast address are delivered to a single interface.
  • B. Packets are delivered to all interfaces identified by the address. This is also called a one-to-many address.
  • C. Identifies multiple interfaces and is only delivered to one address. This address can also be called one-to-one-of-many.
  • D. These addresses are meant for nonrouting purposes, but they are almost globally unique so it is unlikely they will have an address overlap.

  • Correct Answer
  • Packets are delivered to all interfaces identified by the address. This is also called a one-to-many address. 

    Explanation
    Packets addressed to a multicast address are delivered to all interfaces identified by the multicast address, the same as in IPv4. It is also called a one-to-many address. You can always tell a multicast address in IPv6 because multicast addresses always start with FF.

  • More questions

    • 1. What command will permit SMTP mail to only host 1.1.1.1?

    • Options
    • A. access-list 10 permit smtp host 1.1.1.1
    • B. access-list 110 permit ip smtp host 1.1.1.1
    • C. access-list 10 permit tcp any host 1.1.1.1 eq smtp
    • D. access-list 110 permit tcp any host 1.1.1.1 eq smtp
    • Discuss
    • 2. The Corporate router receives an IP packet with a source IP address of 192.168.214.20 and a destination address of 192.168.22.3. Looking at the output from the Corporate router, what will the router do with this packet?
      Corp#sh ip route
      [output cut]
      R    192.168.215.0 [120/2] via 192.168.20.2, 00:00:23, Serial0/0
      R    192.168.115.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0
      R    192.168.30.0 [120/1] via 192.168.20.2, 00:00:23, Serial0/0
      C    192.168.20.0 is directly connected, Serial0/0
      C    192.168.214.0 is directly connected, FastEthernet0/0

    • Options
    • A. The packet will be discarded.
    • B. The packet will be routed out the S0/0 interface.
    • C. The router will broadcast looking for the destination.
    • D. The packet will be routed out the Fa0/0 interface.
    • Discuss
    • 3. Which statement(s) about IPv4 and IPv6 addresses are true?

      1. An IPv6 address is 32 bits long, represented in hexidecimal.
      2. An IPv6 address is 128 bits long, represented in decimal.
      3. An IPv4 address is 32 bits long, represented in decimal.
      4. An IPv6 address is 128 bits long, represented in hexidecimal.

    • Options
    • A. 1 and 3 only
    • B. 2 only
    • C. 3 and 4
    • D. 2 and 4
    • Discuss
    • 4. When a new trunk link is configured on an IOS-based switch, which VLANs are allowed over the link?

    • Options
    • A. By default, all VLANs are allowed on the trunk.
    • B. No VLAN's are allowed, you must configure each VLAN by hand.
    • C. Only configured VLAN's are allowed on the link.
    • D. Only extended VLAN's are allowed by default.
    • Discuss
    • 5. In Cisco's Unified Wireless Solution, what is the split-MAC architecture?

    • Options
    • A. The split-MAC architecture uses MAC addresses to create a forward/filter table and break up collision domains.
    • B. The split-MAC architecture allows the splitting of 802.11 protocol packets between the AP and the controller to allow processing by both devices.
    • C. The split-MAC architecture uses MAC addresses on the wireless network and IP addresses on the wired network.
    • D. The split-MAC architecture uses MAC addresses to create a forward/filter table and break up broadcast domains.
    • Discuss
    • 6. You are working on a router that has established privilege levels that restrict access to certain functions. You discover that you are not able to execute the command show running-configuration. How can you view and confirm the access lists that have been applied to the Ethernet 0 interface on your router?

    • Options
    • A. show access-lists
    • B. show interface Ethernet 0
    • C. show ip access-lists
    • D. show ip interface Ethernet 0
    • Discuss
    • 7. What information is displayed by the show hosts command?

      1. Temporary DNS entries
      2. The names of the routers created using the hostname command
      3. The IP addresses of workstations allowed to access the router
      4. Permanent name-to-address mappings created using the ip host command
      5. The length of time a host has been connected to the router via Telnet

    • Options
    • A. 1, 2 and 3
    • B. 1 and 4
    • C. 3, 4, and 5
    • D. All of the above
    • Discuss
    • 8. You want to create a standard access list that denies the subnet of the following host: 172.16.144.17/21. Which of the following would you start your list with?

    • Options
    • A. access-list 10 deny 172.16.48.0 255.255.240.0
    • B. access-list 10 deny 172.16.144.0 0.0.7.255
    • C. access-list 10 deny 172.16.64.0 0.0.31.255
    • D. access-list 10 deny 172.16.136.0 0.0.15.255
    • Discuss
    • 9. Your company is running IGRP using an AS of 10. You want to configure EIGRP on the network but want to migrate slowly to EIGRP and don't want to configure redistribution. What command would allow you to migrate over time to EIGRP without configuring redistribution?

    • Options
    • A. router eigrp 11
    • B. router eigrp 10
    • C. router eigrp 10 redistribute igrp
    • D. router igrp combine eigrp 10
    • Discuss
    • 10. Which of the following commands sets a trunk port on a 2960 switch?

    • Options
    • A. trunk on
    • B. trunk all
    • C. switchport trunk on
    • D. switchport mode trunk
    • Discuss


    Comments

    There are no comments.

Enter a new Comment