Discussion
Home ‣ Certification ‣ CISCO Certification Comments
- Question
You are the administrator of network X. You decided to implement RIP in the following topology (click exhibit). You do not want R3 to receive RIP updates. What configuration changes need to be implemented?
Options- A. Implement a passive-interface on R1
- B. Nothing needs to be configured
- C. Create a sub-interface on R1
- D. Change the routing protocol to OSPF
- Correct Answer
- Implement a passive-interface on R1
ExplanationExplanation: To block RIP broadcasts on an interface connected to a subnet of a RIP-enabled network add the passive-interface command to the RIP Process
- 1. As a network administrator we want to make it easy to assign IP addresses to hosts. What protocol do we use?
Options- A. DNS
- B. DHCP
- C. HSRP
- D. NTP Discuss
- 2. What is the meaning of amber SYST led on a 2960 switch?
Options- A. This is normal operation
- B. There is a bridging loop
- C. The switch IOS is loading
- D. The switch failed its POST Discuss
- 3. What command will change the hostname of a router?
Options- A. router#host name new name
- B. router(config-router)#hostname new name
- C. router>host name new name
- D. router(config)#hostname new name Discuss
- 4. Which of the following symbols indicate that a ping was successful?
Options- A. !
- B. .
- C. ?
- D. U Discuss
- 5. What do you use when you want to display a message to all the terminals connected to a router?
Options- A. banner login
- B. banner motd
- C. banner exec
- D. banner slip-ppp Discuss
- 6. Which layer of the OSI model is associated with LAN switches?
Options- A. The Transport layer.
- B. The Physical layer.
- C. The Network layer.
- D. The Data Link layer. Discuss
- 7. Which layer of the OSI model is associated with HDLC, Frame Relay and PPP?
Options- A. The Physical Layer
- B. The Data Link layer
- C. The Transport Layer
- D. The Network Layer Discuss
- 8. What is meant by same layer interaction
Options- A. That a packet is forwarded to a different host that resides in the same layer of the Cisco three layer hierarchical model.
- B. That an interaction occurs within a single layer of a networking model and that no other layers or devices take any part in the interaction.
- C. An interaction that progresses up or down only one level of a networking model.
- D. That two computers use a protocol defined at the same layer of a networking model to communicate with each other. Discuss
- 9. A device on a network is ready to send a frame. What is the first thing that CSMA/CD logic does?
Options- A. Sends a token out to instruct other devices not to send packets.
- B. Sends a jamming signal out to prevent other hosts from sending packets.
- C. Sends a discovery message out to find out if the destination host is on the same subnet.
- D. Listens to see if the Ethernet is busy. Discuss
- 10. What does CSMA/CD stand for?
Options- A. Carrier Sense Multiple Action with Collision Detection.
- B. Carrier Sense Multiple Access with Collisionless Delivery
- C. Carrier Sense Multiple Action with Collision Detonation
- D. Carrier Sense Multiple Access with Collision Detection Discuss
CISCO Certification problems
Search Results
Correct Answer: DHCP
Explanation:
Explanation: DHCP, as described by RFC 1541, or Dynamic Host Configuration Protocol is used for dynamically assigning network addresses and host specific configuration parameters.
Correct Answer: The switch failed its POST
Explanation:
Explanation: When the switch failed its POST, Power-On Self Test, the SYST led will turn amber and the IOS did not load
Correct Answer: router(config)#hostname new name
Explanation:
Explanation: To specify or modify the host name for the network server, use the hostname command in global configuration mode.
Correct Answer: !
Explanation:
Explanation: The following table explains the output generated by ping:
! ? reply received
. ? timed out
U ? unreachable
C ? congestion
? ? unknown packet type
& packet lifetime exceeded
Correct Answer: banner motd
Explanation:
Explanation: This MOTD banner is displayed to all terminals connected and is useful for sending messages that affect all users (such as impending system shutdowns). Use the no exec-banner or no motd-banner command to disable the MOTD banner on a line. The no exec-banner command also disables the EXEC banner on the line. When a user connects to the router, the MOTD banner appears before the login prompt. After the user logs in to the router, the EXEC banner or incoming banner will be displayed, depending on the type of connection. For a reverse Telnet login, the incoming banner will be displayed. For all other connections, the router will display the EXEC banner. Connection, Menu, and System Banner Commands
Correct Answer: The Data Link layer.
Correct Answer: The Data Link layer
Correct Answer: That two computers use a protocol defined at the same layer of a networking model to communicate with each other.
Correct Answer: Listens to see if the Ethernet is busy.
Correct Answer: Carrier Sense Multiple Access with Collision Detection
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.