Discussion
Home ‣ Certification ‣ CISCO Certification Comments
- Question
Convert the following from binary format to decimal IP address. 11001100.00110011.10101010.01010101
- Correct Answer
- Answer
- 1. What is the purpose of flow control?
Options- A. To ensure that data is retransmitted if an acknowledgment is not received
- B. To reassemble segments in the correct order at the destination device
- C. To provide a means for the receiver to govern the amount of data sent by the sender
- D. To regulate the size of each segment Discuss
- 2. Why is BGP a better choice for Internet routing than the IGPs? Discuss
- 3. By default , what type of trust are all Windows 2000 trust relationships within a domain tree or forest?
Options- A. Explicit trust
- B. One-way trust
- C. Transitive trust
- D. Non-transitive trust Discuss
- 4. Which of the following is an industry-wide standards suite of protocols and algorithms that allows for secure data transmission over an IP-based network that functions at the layer3 Network layer of the OSI model?
Options- A. HDLC
- B. xDSL
- C. VPN
- D. IPSec Discuss
- 5. An administrator issues the command "ping 127.0.0.1" from the command line prompt on a PC host named PC1. If an ICMP reply is received, what does this confirm? A. The PC host PC1 has connectivity with a local host B. The PC host PC1 has connectivity with a Layer 3 device C. The PC host PC1 has a default gateway correctly configured D. The PC host PC1 has connectivity up to Layer 5 of the OSI model E. The PC host PC1 has the TCP/IP protocol stack correctly installed Discuss
- 6. A default Frame Relay WAN is classified as what type of physicalnetwork? A: broadcast point-to-multi point B: broadcast multi-access C: non broadcast multi-access D: non broadcast multi-point Discuss
- 7. Which two descriptions are correct about characteristics of IPv6 unicast addressing? (Choose two) A. Global addresses start with 2000::/3. B. Link-local addresses start with FF00::/10. C. Link-local addresses start with FE00:/12. D. There is only one loopback address and it is ::1. Discuss
- 8. You want to implement a mechanism that automates the IP configuration, including IP address, subnet mask, default gateway, and DNS information. Which protocol will you use to accomplish this?
Options- A. SMTP
- B. SNMP
- C. DHCP
- D. ARP Discuss
- 9. What does the command confreg 0x2142 provide?
Options- A. It is used to restart the router
- B. It is used to bypass the configuration in NVRAM
- C. It is used to enter ROM monitor mode
- D. It is used to view the lost password Discuss
- 10. If you want to disable STP on a port connected to a server, which command would you use?
Options- A. disable spanning-tree
- B. spanning-tree off
- C. spanning-tree security
- D. spanning-tree portfast Discuss
CISCO Certification problems
Search Results
Correct Answer: To provide a means for the receiver to govern the amount of data sent by the sender
Explanation:
Flow control allows the receiving device to control the transmitter so the receiving device's buffer does not overflow.
Correct Answer: RIP version 1 and IGRP are classful protocols and do not advertise subnet mask information RIP version 2 has a limited network diameter of 15 hops EIGRP, OSPF, and IS-IS use computational intensive algorithms for determining a shortest path BGP relies on simple techniques for best path selection and loop detection, and can handle the number of network prefixes required for Internet routing
Correct Answer: Transitive trust
Explanation:
By default, all Windows 2000 trusts within a domain tree or forest are transitive trusts.
Correct Answer: IPSec
Explanation:
IPSec is an industry-wide standard suite of protocols and algorithms that allows for secure data transmission over an IP-based network that functions at the layer3 Network layer of the OSI model.
Correct Answer: : E
Correct Answer: : C Explanation: FrameRelay, ATM, and X25 are non-broadcast multiple access (NBMA) networks NBMA networks allow only data transfer from one computer to another over a VC or across a switching device NBMA networks do not support multicast or broadcast traffic FrameRelay, ATM, and X25 are non-broadcast multiple access (NBMA) networks NBMA networks allow only data transfer from one computer to another over a VC or across a switching device NBMA networks do not support multicast or broadcast traffic - See more at: https://wwworbitco-ccna-pastquestionscom/CCNA-Past-Questions%3A-WANphp#sthashhb05ZKYsdpuf
Correct Answer: : A , D Explanation: An IPv6 Unicast address identifies a single network interface The Internet Protocol delivers packets sent to a unicast address to that specific interface
Correct Answer: DHCP
Explanation:
Dynamic Host Configuration Protocol (DHCP) is used to provide IP information to hosts on your network. DHCP can provide a lot of information, but the most common is Ip address, subnet mask, default gateway, and DNS information.
Correct Answer: It is used to bypass the configuration in NVRAM
Explanation:
The default configuration setting is 0x2102, which tells the router to load the IOS from flash and the configuration from NVRAM. 0x2142 tells the router to bypass the configuration in NVRAM so that you can perform password recovery.
Correct Answer: spanning-tree portfast
Explanation:
If you have a server or other devices connected into your switch that you're totally sure won't create a switching loop if STP is disabled, you can use something called portfast on these ports. Using it means the port won't spend the usual 50 seconds to come up while STP is converging.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.