CuriousTab
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank Clerk
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Electronics
‣
Standard Logic Devices (SLD)
See What Others Are Saying!
Question
NMOS devices use MOSFETs to implement the full range of logic gates using the universal NAND gate.
Options
A. True
B. False
Correct Answer
False
More questions
1. The amount of dc current that an inductor will allow to pass depends on the circuit's total resistance that is in series with it.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
2.
The total capacitance in the given circuit is larger than the value of C
4
.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
3.
A ___ is created when an electron moves from the valence band to the conduction band.
Options
A. hole
B. gap
C. vacancy
D. blank
Show Answer
Scratch Pad
Discuss
Correct Answer: hole
4. Operational amplifiers (op-amps) use internal capacitive coupling between stages.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
5. The time interval between the memory receiving a new address input and the data being available is called _________.
Options
A. access time
B. bus speed
C. read/write speed
D. write/data speed
Show Answer
Scratch Pad
Discuss
Correct Answer: access time
6. A half-cycle average voltage of 12 V is equal to what rms voltage?
Options
A. 13.33 V
B. 8.48 V
C. 18.84 V
D. 7.64 V
Show Answer
Scratch Pad
Discuss
Correct Answer: 13.33 V
7. A parallel circuit is sometimes called a current divider.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
8. The n-type semiconductor material is doped by adding material with electron holes.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
9. In a series
RC
circuit, the phase difference between the current and the source voltage _____.
Options
A. depends on the values of
R
and
C
B. equals 0°
C. equals 90°
D. depends on the amplitude of the input voltage
Show Answer
Scratch Pad
Discuss
Correct Answer: depends on the values of
R
and
C
10. A technique of addressing storage cells on a dynamic RAM that sequentially uses the same inputs for the row and column addresses of the cell is called________.
Options
A. flash conversion
B. dynamic refresh
C. address multiplexing
D. address strobe
Show Answer
Scratch Pad
Discuss
Correct Answer: address multiplexing
Comments
There are no comments.
Enter a new Comment
Save
More in Electronics:
Alternating Current and Voltage
Alternating Current vs Direct Current
Analog and Digital Converters
Analog to Digital
Arithmetic Operations and Circuits
Basic Op-Amp Circuits
Bipolar Junction Transistors (BJT)
Capacitors
Combinational Logic Circuits
Computer Hardware and Software
Diodes and Applications
Field Effect Transistors (FET)
Flip-Flops and Timers
Inductors
Logic Circuit Simplification
Logic Gates
Magnetism and Electromagnetism
Measurement, Conversion and Control
Number Systems and Codes
Ohm's Law
Operational Amplifiers
Parallel Circuits
Programmable Logic Devices (PLD)
Quantities and Units
RC Circuits
Resistance and Power
RL Circuits
RLC Circuits and Resonance
Semiconductor Memory
Semiconductor Principles
Sequential Logic Circuits
Series-Parallel Circuits
Series Circuits
Special-Purpose Op-Amp Circuits
Standard Logic Devices (SLD)
Testing and Troubleshooting
Thyristors and Tranducers
Time Response of Reactive Circuits
Transformers
Transistors and Applications
Voltage and Current