CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Electronics
‣
Analog to Digital
Comments
Question
Digital systems using the 10-state system are more accurate than those using the two-state system.
Options
A. True
B. False
Correct Answer
False
Analog to Digital problems
Search Results
1. The voltages in digital electronics are continuously variable.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
2. Breakdown voltage and pinch-off voltage of a JFET are different terms for the same voltage level.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
3. A D-MOSFET cannot be biased using zero biasing.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
4. If the drain, source, and channel are all a p-type material, and the transistor operates in both modes, this is a p-channel E-MOSFET.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
5. A common-drain configured JFET is also called a source-follower.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
6. The decimal code system used ten levels of voltage.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
7. The coded group of pulses in a digital electronic circuit consists of a series of HIGH and LOW voltages.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
8. In digital electronic circuits, information is first converted to a coded group of pulses.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
9. Digitizing a signal converts it from digital to analog.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
10. Most of the input signals applied to a computer for storage or processing are digital in nature.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
Comments
There are no comments.
Enter a new Comment
Save
More in Electronics:
Alternating Current and Voltage
Alternating Current vs Direct Current
Analog and Digital Converters
Analog to Digital
Arithmetic Operations and Circuits
Basic Op-Amp Circuits
Bipolar Junction Transistors (BJT)
Capacitors
Combinational Logic Circuits
Computer Hardware and Software
Diodes and Applications
Field Effect Transistors (FET)
Flip-Flops and Timers
Inductors
Logic Circuit Simplification
Logic Gates
Magnetism and Electromagnetism
Measurement, Conversion and Control
Number Systems and Codes
Ohm's Law
Operational Amplifiers
Parallel Circuits
Programmable Logic Devices (PLD)
Quantities and Units
RC Circuits
Resistance and Power
RL Circuits
RLC Circuits and Resonance
Semiconductor Memory
Semiconductor Principles
Sequential Logic Circuits
Series-Parallel Circuits
Series Circuits
Special-Purpose Op-Amp Circuits
Standard Logic Devices (SLD)
Testing and Troubleshooting
Thyristors and Tranducers
Time Response of Reactive Circuits
Transformers
Transistors and Applications
Voltage and Current