CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Electronics
‣
Operational Amplifiers
Comments
Question
A monostable multivibrator must be triggered.
Options
A. True
B. False
Correct Answer
True
Operational Amplifiers problems
Search Results
1. If an input signal is applied to the inverting input of an op-amp with the noninverting input grounded, the output signal would be opposite in polarity with the input.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
2. If the two inputs to a differential amplifier are exactly the same, then the output is the signal multiplied by two.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
3. The frequency of a crystal is dependent on how much voltage is applied to activate it.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
4. An S-R flip-flop is an example of a bistable multivibrator circuit.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
5. An open feedback resistor in an inverting or noninverting op-amp circuit can cause severe clipping of the output signal.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
6. The difference between the upper and lower trigger points is called the Schmitt trigger.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
7. The inverting input is pin 2.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
8. A voltage-follower op-amp has the output connected directly to the inverting input.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
9. This circuit is a bandpass filter.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
10.
The voltage gain of the amplifier in the given circuit would increase if ______.
Options
A. the feedback resistor was decreased in value
B. the input voltage was increased
C. the input resistor was increased in value
D. None of the above
Show Answer
Scratch Pad
Discuss
Correct Answer: None of the above
Comments
There are no comments.
Enter a new Comment
Save
More in Electronics:
Alternating Current and Voltage
Alternating Current vs Direct Current
Analog and Digital Converters
Analog to Digital
Arithmetic Operations and Circuits
Basic Op-Amp Circuits
Bipolar Junction Transistors (BJT)
Capacitors
Combinational Logic Circuits
Computer Hardware and Software
Diodes and Applications
Field Effect Transistors (FET)
Flip-Flops and Timers
Inductors
Logic Circuit Simplification
Logic Gates
Magnetism and Electromagnetism
Measurement, Conversion and Control
Number Systems and Codes
Ohm's Law
Operational Amplifiers
Parallel Circuits
Programmable Logic Devices (PLD)
Quantities and Units
RC Circuits
Resistance and Power
RL Circuits
RLC Circuits and Resonance
Semiconductor Memory
Semiconductor Principles
Sequential Logic Circuits
Series-Parallel Circuits
Series Circuits
Special-Purpose Op-Amp Circuits
Standard Logic Devices (SLD)
Testing and Troubleshooting
Thyristors and Tranducers
Time Response of Reactive Circuits
Transformers
Transistors and Applications
Voltage and Current