CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Electronics
‣
Operational Amplifiers
Comments
Question
Crystal oscillator circuits have a very low Q.
Options
A. True
B. False
Correct Answer
False
Operational Amplifiers problems
Search Results
1. The ideal output impedance for an
operational amplifier
is 0 Ω.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
2. If the two inputs to a differential amplifier are exactly the same, then the output is the signal multiplied by 2.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
3. If an input signal is applied to the inverting input of an op-amp with the noninverting input grounded, the output signal would be opposite in polarity to the input.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
4. An
inverting amplifier
has a phase shift of 180° from input to output.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
5.
The output voltage is _____ at the resonant frequency in the given circuit.
Options
A. 0 mV
B. 31.4 mV
C. 66.5 mV
D. 380 mV
Show Answer
Scratch Pad
Discuss
Correct Answer: 66.5 mV
6. Feedback is used in an open-loop operational amplifier circuit.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
7. An astable multivibrator has two states.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
8. The feedback resistor adds to the gain of an op-amp.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
9. It takes 4 µs for the output voltage of an op-amp to rise from ?14 V to +14 V. The
slew rate
of this op-amp is 3.5 V/µs.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
10. In a common-mode input to an op-amp, both inputs are connected to the same signal source.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
Comments
There are no comments.
Enter a new Comment
Save
More in Electronics:
Alternating Current and Voltage
Alternating Current vs Direct Current
Analog and Digital Converters
Analog to Digital
Arithmetic Operations and Circuits
Basic Op-Amp Circuits
Bipolar Junction Transistors (BJT)
Capacitors
Combinational Logic Circuits
Computer Hardware and Software
Diodes and Applications
Field Effect Transistors (FET)
Flip-Flops and Timers
Inductors
Logic Circuit Simplification
Logic Gates
Magnetism and Electromagnetism
Measurement, Conversion and Control
Number Systems and Codes
Ohm's Law
Operational Amplifiers
Parallel Circuits
Programmable Logic Devices (PLD)
Quantities and Units
RC Circuits
Resistance and Power
RL Circuits
RLC Circuits and Resonance
Semiconductor Memory
Semiconductor Principles
Sequential Logic Circuits
Series-Parallel Circuits
Series Circuits
Special-Purpose Op-Amp Circuits
Standard Logic Devices (SLD)
Testing and Troubleshooting
Thyristors and Tranducers
Time Response of Reactive Circuits
Transformers
Transistors and Applications
Voltage and Current