CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Electronics
‣
Parallel Circuits
Comments
Question
Current divider predicts that the most current will flow in the parallel path of the most resistance.
Options
A. True
B. False
Correct Answer
False
Parallel Circuits problems
Search Results
1. The largest branch resistance in a parallel circuit carries the largest branch current.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
2. If a branch opens in a parallel circuit, the current in the remaining parallel paths will change.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
3. In a flash analog-to-digital converter, the output of each comparator is connected to an input of a:
Options
A. decoder
B. priority encoder
C. multiplexer
D. demultiplexer
Show Answer
Scratch Pad
Discuss
Correct Answer: priority encoder
4. Sample-and-hold circuits in analog-to digital converters (ADCs) are designed to:
Options
A. sample and hold the output of the binary counter during the conversion process
B. stabilize the comparator's threshold voltage during the conversion process
C. stabilize the input analog signal during the conversion process
D. sample and hold the D/A converter staircase waveform during the conversion process
Show Answer
Scratch Pad
Discuss
Correct Answer: stabilize the input analog signal during the conversion process
5. Which is not an analog-to-digital (ADC) conversion error?
Options
A. differential nonlinearity
B. missing code
C. incorrect code
D. offset
Show Answer
Scratch Pad
Discuss
Correct Answer: differential nonlinearity
6. The total resistance of a parallel circuit is always greater than the largest resistor value.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
7. If one of the resistors opens in a parallel circuit branch, the total resistance of the circuit will decrease.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
8. The total resistance in a parallel circuit is always less than the least resistor.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
9. The total power dissipated is 4.8 watts.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
10. If a branch opens in a parallel circuit, the total circuit resistance decreases.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
Comments
There are no comments.
Enter a new Comment
Save
More in Electronics:
Alternating Current and Voltage
Alternating Current vs Direct Current
Analog and Digital Converters
Analog to Digital
Arithmetic Operations and Circuits
Basic Op-Amp Circuits
Bipolar Junction Transistors (BJT)
Capacitors
Combinational Logic Circuits
Computer Hardware and Software
Diodes and Applications
Field Effect Transistors (FET)
Flip-Flops and Timers
Inductors
Logic Circuit Simplification
Logic Gates
Magnetism and Electromagnetism
Measurement, Conversion and Control
Number Systems and Codes
Ohm's Law
Operational Amplifiers
Parallel Circuits
Programmable Logic Devices (PLD)
Quantities and Units
RC Circuits
Resistance and Power
RL Circuits
RLC Circuits and Resonance
Semiconductor Memory
Semiconductor Principles
Sequential Logic Circuits
Series-Parallel Circuits
Series Circuits
Special-Purpose Op-Amp Circuits
Standard Logic Devices (SLD)
Testing and Troubleshooting
Thyristors and Tranducers
Time Response of Reactive Circuits
Transformers
Transistors and Applications
Voltage and Current