CuriousTab
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank Clerk
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Environmental Engineering
See What Others Are Saying!
Question
Which of the following air pollutants is not toxic to vegetation i.e., doesn't cause vegetation damage?
Options
A. Smog & ozone
B. Hydrogen fluoride & nitrogen oxides
C. Sulphur dioxide & spray of weed killers
D. Carbon monoxide
Correct Answer
Carbon monoxide
More questions
1. Dew point of a gas-vapour mixture
Options
A. increases with temperature rise.
B. decreases with temperature rise.
C. decreases with decrease in pressure.
D. increases with increase in pressure.
Show Answer
Scratch Pad
Discuss
Correct Answer: decreases with decrease in pressure.
2. 'Six-tenth factor' rule is used for estimating the
Options
A. equipment installation cost.
B. equipment cost by scaling.
C. cost of piping.
D. utilities cost.
Show Answer
Scratch Pad
Discuss
Correct Answer: equipment cost by scaling.
3. The payback method for the measurement of return on investment
Options
A. gives a correct picture of profitability.
B. underemphasises liquidity.
C. does not measure the discounted rate of return.
D. takes into account the cash inflows after the recovery of investments.
Show Answer
Scratch Pad
Discuss
Correct Answer: does not measure the discounted rate of return.
4. In a manufacturing industry, break even point occurs, when the
Options
A. total annual rate of production equals the assigned value.
B. total annual product cost equals the total annual sales.
C. annual profit equals the expected value.
D. annual sales equals the fixed cost.
Show Answer
Scratch Pad
Discuss
Correct Answer: total annual product cost equals the total annual sales.
5. Washability curve based on float and sink test enables an assessment to be made of the possibility of cleaning a coal fraction based on the
Options
A. density separation.
B. differential wettability.
C. size.
D. volatile matter content.
Show Answer
Scratch Pad
Discuss
Correct Answer: density separation.
6. Buna-S is a __________ material.
Options
A. fibrous
B. plastic
C. resinous
D. rubbery
Show Answer
Scratch Pad
Discuss
Correct Answer: rubbery
7. Compressibility factor for almost all the gases are approximately same at the same
Options
A. pressure and temperature.
B. reduced pressure and reduced temperature.
C. critical pressure and critical temperature.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: reduced pressure and reduced temperature.
8. In a distillation column, bubble caps are located on trays with a pitch of __________ times the outside diameter of the caps.
Options
A. 1.3 to 2
B. 1.6 to 2
C. 2.5
D. 1.5 to 3
Show Answer
Scratch Pad
Discuss
Correct Answer: 1.3 to 2
9. Aerodynamic noise resulting from turbulent gas flow is the most prevalent source of valve noise in fluid ilow control. It is caused due to
Options
A. Reynold stresses
B. shear forces
C. both (a) & (b)
D. neither (a) nor (b)
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) & (b)
10. Paddle agitator
Options
A. is suitable for mixing low viscosity liquids.
B. produces axial flow.
C. moves at very high speed.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: is suitable for mixing low viscosity liquids.
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry