Discussion
Home ‣ Chemical Engineering ‣ Mechanical Operations Comments
- Question
During washing of filter at the end of constant pressure filtration, the rate of washing equals the rate of filtration
Options- A. at time zero.
- B. at the end of filtration.
- C. when half the filtrate has been obtained.
- D. at the end of filtration, but decreases with time subsequently.
- Correct Answer
- at the end of filtration.
- 1. Tube mill compared to ball mill
Options- A. produces finer products.
- B. is long in comparison with its diameter.
- C. uses smaller balls.
- D. all (a), (b) & (c). Discuss
- 2. For spheres, the surface shape factor is given by (where, A = area, V = volume, and D = diameter)
Options- A. ?(=A/D2)
- B. ?/6(=V/D3)
- C.
- D. None of these. Discuss
- 3. Crushing efficiency of a machine ranges between __________ percent.
Options- A. 0.1 to 2
- B. 5 to 10
- C. 20 to 25
- D. 50 to 70 Discuss
- 4. Separation of solid suspended in liquid into a supernatant clear liquid and a denser slurry employs a process termed as the
Options- A. coagulation
- B. flocculation
- C. sedimentation
- D. clarification Discuss
- 5. Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher?
Options- A. Rod mill
- B. Fluid energy mill
- C. Gyratory crusher
- D. Ball mill Discuss
- 6. Filter medium resistance is that offered by the
Options- A. filter cloth.
- B. embedded particles in the septum.
- C. filter cloth and the embedded particle collectively.
- D. none of these. Discuss
- 7. Filtration operation carried out by continuous increase of the inlet pressure of slurry, is called the __________ filtration.
Options- A. constant rate
- B. varying pressure
- C. varying rate
- D. constant pressure Discuss
- 8. The reduction ratio for grinders is defined as(where, Df and Dp are average diameters of feed and product respectively).
Options- A. Df/Dp
- B. Dp/Df
- C. Df - Dp
- D. none of these Discuss
- 9. Fluid energy mill comes in the category of
Options- A. grinder
- B. crusher
- C. cutter
- D. ultrafine grinder Discuss
- 10. Pick out the wrong statement pertaining to the turbine agitator.
Options- A. Recommended peripheral speed for the turbine agitator is 200-250 metres/minute.
- B. Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow.
- C. Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter).
- D. Turbine agitator should be located at a height not less than one agitator diameter length from the bottom. If the depth of liquid in the tank is more than twice the agitator diameter, two agitators should be used. Discuss
Mechanical Operations problems
Search Results
Correct Answer: all (a), (b) & (c).
Correct Answer: ?(=A/D2)
Correct Answer: 0.1 to 2
Correct Answer: sedimentation
Correct Answer: Gyratory crusher
Correct Answer: filter cloth and the embedded particle collectively.
Correct Answer: constant rate
Correct Answer: Df/Dp
Correct Answer: ultrafine grinder
Correct Answer: Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow.
Comments
There are no comments.More in Chemical Engineering:
Programming
Copyright ©CuriousTab. All rights reserved.