logo

CuriousTab

CuriousTab

Discussion

Home ‣ Civil Engineering ‣ RCC Structures Design Comments
  • Question

  • Enlarged head of a supporting column of a flat slabs is technically .known as


  • Options
  • A. supporting end of the column
  • B. top of the column
  • C. capital
  • D. drop panel
  • E. none of these.

  • Correct Answer
  • capital 

    • RCC Structures Design problems

    Search Results

    • 1. A ribbed slab is provided for

    • Options
    • A. a plain ceiling
    • B. thermal insulation
    • C. acoustic insulation
    • D. all the above.
      • Discuss
    • 2. In a cantilever retaining wall without a heel slab

    • Options
    • A. thickness of the stem is kept same throughout
    • B. base slab is made 10 cm thicker than the stem
    • C. width of the base slab is kept 0.7 time the total height of the wall
    • D. all the above.
      • Discuss
    • 3. A column is regarded as long column if the ratio of its effective length and lateral dimension, exceeds

    • Options
    • A. 10
    • B. 15
    • C. 20
    • D. 25
    • E. 30
      • Discuss
    • 4. If L is the effective span of a R.C.C. beam which is subjected to maximum shear qmax at the ends, the distance from either end over which stirrups for the shear, are provided, is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 5. If the length of a combined footing for two columns l metres apart is L and the projection on the left side of the exterior column is x, then the projection y on the right side of the exterior column, in order to have a uniformly distributed load, is (where x is the distance of centre of gravity of column loads).

    • Options
    • A. y = L - (l - x)
    • B.
    • C.
    • D.
      • Discuss
    • 6. If A is the area of the foundation of a retaining wall carrying a load W and retaining earth of weight w per unit volume, the minimum depth (h) of the foundation from the free surface of the earth, is

    • Options
    • A.
    • B.
    • C.
    • D.
      • Discuss
    • 7. The width of the flange of a L-beam, should be less than

    • Options
    • A. one-sixth of the effective span
    • B. breadth of the rib + four times thickness of the slab
    • C. breadth of the rib + half clear distance between ribs
    • D. least of the above.
      • Discuss
    • 8. The structure constructed to allow drainage water to flow under pressure through an inverted syphon below a canal, is called

    • Options
    • A. syphon
    • B. super passage
    • C. aqueduct
    • D. super-aqueduct
    • E. syphon aqueduct.
      • Discuss
    • 9. The sensitivity of a rigid module, is

    • Options
    • A. 2.00
    • B. 1.50
    • C. 1.00
    • D. 0.50
    • E. zero
      • Discuss
    • 10. A hydraulic jump is generally formed when a stream moving with

    • Options
    • A. a hyper-critical velocity meets a stream moving with a critical velocity
    • B. a hyper-critical velocity meets a stream moving with a hyper-critical velocity
    • C. A hyper-critical velocity meets a stream moving with a sub-critical velocity
    • D. a sub-critical velocity meets a stream moving with a hyper-critical velocity.
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.