CuriousTab
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank Clerk
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Digital Electronics
‣
The 8051 Microcontroller
See What Others Are Saying!
Question
The special function registers are maintained in the next 128 locations after the general-purpose data storage and stack.
Options
A. True
B. False
Correct Answer
True
More questions
1. Why is a pull-up resistor needed when connecting TTL logic to CMOS logic?
Options
A. to increase the output LOW voltage
B. to decrease the output LOW voltage
C. to increase the output HIGH voltage
D. to decrease the output HIGH voltage
Show Answer
Scratch Pad
Discuss
Correct Answer: to increase the output HIGH voltage
2. The total sink current decreases with an increase in each load gate input.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
3. The wave-drive sequence of a stepper motor has more torque and operates more smoothly than the full-step sequence at moderate speeds.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
4. In order to select data input
I
1
of a 74151 eight-line multiplexer, the select inputs must be:
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
5. An RC circuit used in a 74122 retriggerable one-shot has an R
EXT
of 100 kΩ and a C
EXT
of 0.005 µF. The pulse width is ________.
Options
A. 70 µs
B. 16 µs
C. 160 µs
D. 32 µs
Show Answer
Scratch Pad
Discuss
Correct Answer: 160 µs
6. When converting from decimal to binary by the repeated division-by-two method, the initial remainder becomes the MSD.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
7. The 74S124 TTL chip is a voltage-controlled oscillator that will generate a specific frequency at
V
out
.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: False
8. A major application for DSP is in ________ and ________ of analog signals.
Options
A. sending, receiving
B. digitizing, weighting
C. filtering, conditioning
D. leveling, translating
Show Answer
Scratch Pad
Discuss
Correct Answer: filtering, conditioning
9. The speed-power product provides a basis for the comparison of logic circuits when power dissipation and propagation delay are important considerations in the selection of the type of logic to be used.
Options
A. True
B. False
Show Answer
Scratch Pad
Discuss
Correct Answer: True
10. An RC circuit used in a nonretriggerable 74121 one-shot has an R
EXT
of 49 kΩ and a C
EXT
of 0.2 µF. The pulse width (t
W
) is approximately ________.
Options
A. 6.9 µs
B. 6.9 ms
C. 69 ms
D. 690 ms
Show Answer
Scratch Pad
Discuss
Correct Answer: 6.9 ms
Comments
There are no comments.
Enter a new Comment
Save
More in Digital Electronics:
Boolean Algebra and Logic Simplification
Code Converters and Multiplexers
Combinational Logic Analysis
Combinational Logic Circuits
Computers
Counters
Describing Logic Circuits
Digital Arithmetic Operations and Circuits
Digital Concepts
Digital Design
Digital Signal Processing
Digital System Projects Using HDL
Ex-OR and Ex-NOR Gates
Flip-Flops
Integrated-Circuit Logic Families
Integrated Circuit Technologies
Interfacing to the Analog World
Logic Families and Their Characteristics
Logic Gates
Memory and Storage
Microprocessor Fundamentals
MSI Logic Circuits
Multivibrators and 555 Timer
Number Systems and Codes
Programmable Logic Device
Shift Registers
Signals and Switches
The 8051 Microcontroller