CuriousTab
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank Clerk
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Process Equipment and Plant Design
See What Others Are Saying!
Question
Where does the maximum tensile strength occur in a thick cylindrical vessel subjected to internal pressure?
Options
A. At the inner surface.
B. At the mid thickness of the cylindrical wall.
C. At the outer surface.
D. None of these.
Correct Answer
At the inner surface.
More questions
1. Chromite refractories are used in
Options
A. bottom of soaking pits.
B. between acid & basic linings in basic open hearth furnaces to prevent their chemical action with each other.
C. both (a) & (b)
D. neither (a) and (b)
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) & (b)
2. If 1 Nm
3
of O
2
contains 'N' number of molecules, then number of molecules in 2Nm
3
of SO
2
will be
Options
A. N
B. N/2
C. 2N
D. 4N
Show Answer
Scratch Pad
Discuss
Correct Answer: 2N
3. Choose the correct statement.
Options
A. Coking tendency increases with increasing molecular weight.
B. Coking tendency decreases with increasing molecular weight.
C. Higher pressure enhances coke formation.
D. Coking is an exothermic reaction.
Show Answer
Scratch Pad
Discuss
Correct Answer: Coking tendency increases with increasing molecular weight.
4. Pure bauxite is the best raw material for the manufacture of high alumina refractories, in which maximum alumina content can be as high as __________ percent.
Options
A. 55
B. 70
C. 80
D. 90
Show Answer
Scratch Pad
Discuss
Correct Answer: 90
5. Vertical storage vessels are never supported by __________ support.
Options
A. bracket
B. saddle
C. skirt
D. lug
Show Answer
Scratch Pad
Discuss
Correct Answer: saddle
6. Maximum permissible concentration (i.e. TLV) of DDT in public water supply system is __________ micro gram (? g)/litre.
Options
A. 2
B. 42
C. 332
D. 1050
Show Answer
Scratch Pad
Discuss
Correct Answer: 42
7. Sulphur content in lighter and heavier petroleum products is generally determined respectively by
Options
A. lamp method and bomb method.
B. bomb method and lamp method.
C. bomb method and quartz tube method.
D. quartz tube method and lamp method.
Show Answer
Scratch Pad
Discuss
Correct Answer: bomb method and lamp method.
8. Permeability of bricks is a measure of the
Options
A. refractoriness.
B. melting point.
C. rate at which a fluid will pass through the pores.
D. expansion during heating.
Show Answer
Scratch Pad
Discuss
Correct Answer: rate at which a fluid will pass through the pores.
9. Pyrometric cone equivalent (PCE) of a refractory is the measure of its
Options
A. spalling resistance.
B. fusion point.
C. resistance to slag penetration.
D. resistance to carbon monoxide attack.
Show Answer
Scratch Pad
Discuss
Correct Answer: fusion point.
10. An azeotropic solution of two liquids has boiling point lower than either of them, when it
Options
A. is saturated.
B. is unsaturated.
C. shows negative deviation from Raoult's law.
D. shows positive deviation from Raoult's law.
Show Answer
Scratch Pad
Discuss
Correct Answer: shows positive deviation from Raoult's law.
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry