CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Stoichiometry
Comments
Question
Pick out the wrong statement.
Options
A. 'Reduced temperature' of a substance is the ratio of its existing temperature to its critical temperature, both expressed on celsius scale.
B. 'Reduced pressure' is the ratio of the existing pressure of a substance to its critical pressure.
C. 'Reduced volume' is the ratio of the existing molal volume of a substance to its critical molal volume.
D. none of these.
Correct Answer
'Reduced temperature' of a substance is the ratio of its existing temperature to its critical temperature, both expressed on celsius scale.
Stoichiometry problems
Search Results
1. One micron is equal to
Options
A. 10
-4
mm
B. 10
-4
cm
C. 10
-6
m
D. both(b)&(c)
Show Answer
Scratch Pad
Discuss
Correct Answer: both(b)&(c)
2. The evaporation of aqueous solution of sugar causes its molarity to
Options
A. decrease. (b) increase.
B. remain unchanged.
C. either (a) or (b); depends on the concentration of the solution.
Show Answer
Scratch Pad
Discuss
Correct Answer: remain unchanged.
3. Heat of solution in a system in which both solute and solvent are liquids is termed as
Options
A. heat of solvation.
B. heat of hydration.
C. standard integral heat of solution.
D. heat of mixing.
Show Answer
Scratch Pad
Discuss
Correct Answer: heat of mixing.
4. The heat change for the reaction, C(s) + 2S(s) ? CS
2
(l), is 104.2 kJ. It represents the heat of
Options
A. formation
B. solution
C. combustion
D. fusion
Show Answer
Scratch Pad
Discuss
Correct Answer: formation
5. In case of a ternery system involving two liquid components and a solute, the ratio of the concentration of the solute in the two phases at equilibrium is called the distribution co-efficient. The distribution co-efficient depends upon the
Options
A. solute concentration
B. temperature
C. both(a) & (b)
D. neither (a) nor (b)
Show Answer
Scratch Pad
Discuss
Correct Answer: both(a) & (b)
6. CaCO
3
contains __________ percent of Ca by weight.
Options
A. 40
B. 48
C. 96
D. 12
Show Answer
Scratch Pad
Discuss
Correct Answer: 40
7. 1 kgf/cm
2
is not equal to
Options
A. 1 torr
B. 1 bar
C. 10000 mm wc
D. 100 KPa = 100 000 N/m
2
Show Answer
Scratch Pad
Discuss
Correct Answer: 1 torr
8. The rate of material __________ is zero in case of a steady state system.
Options
A. accumulation
B. production
C. input
D. generation
Show Answer
Scratch Pad
Discuss
Correct Answer: accumulation
9. Which of the following is not a colligative property?
Options
A. Osmotic pressure
B. Depression of freezing point
C. Lowering of vapor pressure
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: none of these.
10. Pick out the wrong unit conversion of calorific value.
Options
A. 1 kcal/kg = 1.8 BTU/lb = 4.186 kJ/kg.
B. 1 BTU/ft
3
= 8.9 kcal/m
3
= 0.038 MJ/m
3
.
C. 1 BTU/lb = 2.3 kcal/kg.
D. 1 kcal/m
3
= 0.1124 BTU/ft
3
.
Show Answer
Scratch Pad
Discuss
Correct Answer: 1 BTU/lb = 2.3 kcal/kg.
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry