CuriousTab
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank Clerk
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Stoichiometry
See What Others Are Saying!
Question
Osmotic pressure of a dilute solution of a non volatile solute in a solvent obeying Raoult's law is proportional to the
Options
A. temperature.
B. volume of solution.
C. moles of non-volatile solute.
D. none of these.
Correct Answer
temperature.
More questions
1. Pick out the wrong statement.
Options
A. A ferromagnetic material becomes paramagnetic above the 'Curie temperature'.
B. Permanent magnets are made of hard materials, whereas electromagnets require soft magnetic materials.
C. Soft magnetic materials (e.g., pure iron) have higher permeability and low hysterisis loss and coercive forces.
D. Tungsten steel and alnico are not hard magnetic materials.
Show Answer
Scratch Pad
Discuss
Correct Answer: Tungsten steel and alnico are not hard magnetic materials.
2. Dome temperature of blast furnace stove is most accurately measured by a
Options
A. radiation pyrometer.
B. platinum-platinum/rhodium ther-mocuple.
C. iron-constantan thermocouple.
D. platinum resistance thermometer.
Show Answer
Scratch Pad
Discuss
Correct Answer: platinum-platinum/rhodium ther-mocuple.
3. 1 centistoke is equal to __________ Redwood I seconds.
Options
A. 1
B. 4.08
C. 0.408
D. 40.8
Show Answer
Scratch Pad
Discuss
Correct Answer: 4.08
4. Addition of grog in fireclay brick during its manufacture is advantageous, because it results in
Options
A. less shrinkage in heating, decreased apparent porosity & increased specific gravity.
B. high strength & thermal spalling resistance.
C. less addition of water to get a workable plasticity & lesser time required for drying the raw refractories and hence increased rate of production.
D. all (a), (b) and (c).
Show Answer
Scratch Pad
Discuss
Correct Answer: all (a), (b) and (c).
5. The maximum adiabatic flame temperature of fuels in air is __________ the maximum flame temperature in pure oxygen.
Options
A. lower than
B. higher than
C. same as
D. not related to
Show Answer
Scratch Pad
Discuss
Correct Answer: lower than
6. Which of the following is a desirable characteristic of an instrument?
Options
A. High drift
B. High fidelity
C. High measuring lag
D. Poor reproducibility
Show Answer
Scratch Pad
Discuss
Correct Answer: High fidelity
7. A pressure vessel is said to be made of 'thick' shell, if the ratio of its diameter to wall thickness is
Options
A. 10
B. 10
C. 20
D. 20
Show Answer
Scratch Pad
Discuss
Correct Answer: 10
8. For existence of aquatic life in water, the dissolved oxygen content in it, should not be less than __________ ppm.
Options
A. 10000
B. 5
C. 500
D. 1000
Show Answer
Scratch Pad
Discuss
Correct Answer: 5
9. Test piece for determination of RUL of a refractory is heated in a/an
Options
A. oxidising atmosphere
B. reducing atmosphere
C. electric furnace
D. neutral atmosphere
Show Answer
Scratch Pad
Discuss
Correct Answer: electric furnace
10. __________ polymer is used for making unbreakable crockery.
Options
A. Thermoplastic
B. Melamine
C. Addition
D. none of these
Show Answer
Scratch Pad
Discuss
Correct Answer: Melamine
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry