Discussion
Home ‣ Networking ‣ Managing a Cisco Internetwork Comments
- Question
What information is displayed by the show hosts command?
- Temporary DNS entries
- The names of the routers created using the hostname command
- The IP addresses of workstations allowed to access the router
- Permanent name-to-address mappings created using the ip host command
- The length of time a host has been connected to the router via Telnet
Options- A. 1, 2 and 3
- B. 1 and 4
- C. 3, 4, and 5
- D. All of the above
- Correct Answer
- 1 and 4
ExplanationThe show hosts command provides information on temporary DNS entries and permanent name-to-address mappings created using the ip host command. - 1. You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?
Options- A. You didn't boot the router with the correct command.
- B. NVRAM is corrupted.
- C. The configuration register setting is incorrect.
- D. The newly upgraded IOS is not compatible with the hardware of the router. Discuss
- 2. What should the configuration register value be after you successfully complete the password recovery procedure and return the router to normal operation?
Options- A. 0x2100
- B. 0x2101
- C. 0x2102
- D. 0x2142 Discuss
- 3. The configuration register setting of 0x2102 provides what function to a router?
Options- A. Tells the router to boot into ROM monitor mode
- B. Provides password recovery
- C. Tells the router to look in NVRAM for the boot sequence
- D. Boots the IOS from a TFTP server Discuss
- 4. Which command displays the configuration register setting?
Options- A. show ip route
- B. show boot version
- C. show version
- D. show flash Discuss
- 5. Which command will copy the IOS to a backup host on your network?
Options- A. transfer IOS to 172.16.10.1
- B. copy run start
- C. copy start tftp
- D. copy flash tftp Discuss
- 6. You have your laptop directly connected into a router's Ethernet port. Which of the following are among the requirements for the copy flash tftp command to be successful?
- TFTP server software must be running on the router.
- TFTP server software must be running on your laptop.
- The Ethernet cable connecting the laptop directly into the router's Ethernet port must be a straight-through cable.
- The laptop must be on the same subnet as the router's Ethernet interface.
- The copy flash tftp command must be supplied the IP address of the laptop.
Options- A. 1, 3 and 4
- B. 2, 4 and 5
- C. 3 and 5 only
- D. 5 only Discuss
- 7. Which of the following network types have a designated router and a backup designated router assigned?
- Broadcast
- Point-to-point
- NBMA
- NBMA point-to-point
Options- A. 1, 2 and 3
- B. 1 and 3
- C. 3 and 4
- D. All of the above Discuss
- 8. Which of the following protocols support VLSM, summarization, and discontiguous networking?
- RIPv1
- IGRP
- EIGRP
- OSPF
- BGP
- RIPv2
Options- A. 1 and 4
- B. 2 and 5
- C. 3, 4 and 6
- D. All of the above Discuss
- 9. What is the administrative distance of OSPF?
Options- A. 90
- B. 100
- C. 110
- D. 120 Discuss
- 10. Which EIGRP information is held in RAM and maintained through the use of Hello and update packets?
- Neighbor table
- STP table
- Topology table
- DUAL table
Options- A. 2 only
- B. 4 only
- C. 1 and 3
- D. All of the above Discuss
Managing a Cisco Internetwork problems
Search Results
Correct Answer: The configuration register setting is incorrect.
Explanation:
If you save a configuration and reload the router and it comes up either in setup mode or as a blank configuration, chances are you have the configuration register setting incorrect.
Correct Answer: 0x2102
Explanation:
All Cisco routers have a default configuration register setting of
0x2102, which tells the router to load the IOS from flash memory and the configuration from NVRAM.
Correct Answer: Tells the router to look in NVRAM for the boot sequence
Explanation:
The default configuration setting of 0x2102 tells the router to look in NVRAM for the boot sequence.
Correct Answer: show version
Explanation:
The
show version command provides you with the current configuration register setting.
Correct Answer: copy flash tftp
Explanation:
To copy the IOS to a backup host, which is stored in flash memory by default, use the
copy flash tftp command.
Correct Answer: 2, 4 and 5
Explanation:
Before you back up an IOS image to a laptop directly connected to a router's Ethernet port, make sure the TFTP server software is running on your laptop, that the Ethernet cable is a "crossover," and that the laptop is in the same subnet as the router's Ethernet port, and then you can use the
copy flash tftp command from your laptop.
Correct Answer: 1 and 3
Explanation:
No DR is assigned on any type of point-to-point link. No DR/BDR is assigned on the NBMA point-to-multipoint due to the hub/spoke topology. DR and BDR are elected on broadcast and non-broadcast multi-access networks. Frame Relay is a non-Broadcast Multi-Access (NBMA) network by default.
Correct Answer: 3, 4 and 6
Explanation:
RIPv1 and IGRP are true distance-vector routing protocols and can't do much, really-except build and maintain routing tables and use a lot of bandwidth! RIPv2, EIGRP, and OSPF build and maintain routing tables, but they also provide classless routing, which allows for VLSM, summarization, and discontiguous networking.
Correct Answer: 110
Explanation:
The administrative distance (AD) is a very important parameter in a routing protocol. The lower the AD, the more trusted the route. If you have IGRP and OSPF running, by default IGRP routes would be placed in the routing table because IGRP has a lower AD of 100. OSPF has an AD of 110. RIPv1 and RIPv2 both have an AD of 120, and EIGRP is the lowest, at 90.
Correct Answer: 1 and 3
Explanation:
EIGRP holds three tables in RAM: neighbor, topology, and routing. The neighbor and topology tables are built and maintained with the use of Hello packets.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.