Discussion
Home ‣ Networking ‣ Networking Basics Comments
- Question
Which command is used to upgrade an IOS on a Cisco router?
Options- A. copy tftp run
- B. copy tftp start
- C. config net
- D. copy tftp flash
- Correct Answer
- copy tftp flash
ExplanationThe copy tftp flash command places a new file in flash memory, which is the default location for the Cisco IOS in Cisco routers. - 1. How many broadcast domains are created when you segment a network with a 12-port switch?
Options- A. 1
- B. 2
- C. 5
- D. 12 Discuss
- 2. Which command is used to determine if an IP access list is enabled on a particular interface?
Options- A. show access-lists
- B. show interface
- C. show ip interface
- D. show interface access-lists Discuss
- 3. Which router command allows you to view the entire contents of all access lists?
Options- A. show all access-lists
- B. show access-lists
- C. show ip interface
- D. show interface Discuss
- 4. Which protocol does DHCP use at the Transport layer?
Options- A. IP
- B. TCP
- C. UDP
- D. ARP Discuss
- 5. What does the passive command provide to dynamic routing protocols?
Options- A. Stops an interface from sending or receiving periodic dynamic updates.
- B. Stops an interface from sending periodic dynamic updates but not from receiving updates.
- C. Stops the router from receiving any dynamic updates.
- D. Stops the router from sending any dynamic updates. Discuss
- 6. If you wanted to delete the configuration stored in NVRAM, what would you type?
Options- A. erase startup
- B. erase nvram
- C. delete nvram
- D. erase running Discuss
- 7. What does the command routerA(config)#line cons 0 allow you to perform next?
Options- A. Set the Telnet password.
- B. Shut down the router.
- C. Set your console password.
- D. Disable console connections. Discuss
- 8. To back up an IOS, what command will you use?
Options- A. backup IOS disk
- B. copy ios tftp
- C. copy tftp flash
- D. copy flash tftp Discuss
- 9. Which WLAN IEEE specification allows up to 54Mbps at 2.4GHz?
Options- A. A
- B. B
- C. G
- D. N Discuss
- 10. What flavor of Network Address Translation can be used to have one IP address allow many users to connect to the global Internet?
Options- A. NAT
- B. Static
- C. Dynamic
- D. PAT Discuss
Networking Basics problems
Search Results
Correct Answer: 1
Explanation:
By default, switches break up collision domains but are one large broadcast domain.
Correct Answer: show ip interface
Explanation:
The
show ip interface command will show you if any outbound or inbound interfaces have an access list set.
Correct Answer: show access-lists
Explanation:
To see the contents of all access lists, use the
show access-lists command.
Correct Answer: UDP
Explanation:
User Datagram Protocol is a connection network service at the Transport layer, and DHCP uses this connectionless service.
Correct Answer: Stops an interface from sending periodic dynamic updates but not from receiving updates.
Explanation:
The
passive command, short for passive-interface, stops regular updates from being sent out an interface. However, the interface can still receive updates.
Correct Answer: erase startup
Explanation:
The command
erase startup-config deletes the configuration stored in NVRAM.
Correct Answer: Set your console password.
Explanation:
The command
line console 0 places you at a prompt where you can then set your console user-mode password.
Correct Answer: copy flash tftp
Explanation:
The command
copy flash tftp will prompt you to back up an existing IOS in flash to a TFTP host.
Correct Answer: G
Explanation:
IEEE 802.11B is 2.4GHz, but with a maximum of only 11Mbps. IEEE 802.11G is in the 2.4GHz range, with a top speed of 54Mbps.
Correct Answer: PAT
Explanation:
Port Address Translation (PAT) allows a one-to-many approach to network address translation.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.