logo

CuriousTab

CuriousTab

Discussion


Home Electrical Engineering Ohm's Law Comments

  • Question
  • What is the approximate filament resistance of a light bulb if it operates from a 110 V source and 0.6 A of current is flowing?


  • Options
  • A. 183 Ω
  • B. 18.3 Ω
  • C. 66 Ω
  • D. 6.6 Ω

  • Correct Answer
  • 183 Ω 


  • Ohm's Law problems


    Search Results


    • 1. You are measuring the current in a circuit that is operated on an 18 V battery. The ammeter reads 40 mA. Later you notice the current has dropped to 20 mA. How much has the voltage changed?

    • Options
    • A. 9 V
    • B. 900 mV
    • C. 0 V
    • D. 18 V
    • Discuss
    • 2. Twelve volts are applied across a resistor. A current of 3 mA is measured. What is the value of the resistor?

    • Options
    • A. 4 Ω
    • B. 400 Ω
    • C. 4 kΩ
    • D. 4.4 Ω
    • Discuss
    • 3. How much resistance is needed to draw 17.6 mA from a 12 volt source?

    • Options
    • A. 212 Ω
    • B. 6.8 kΩ
    • C. 68 Ω
    • D. 680 Ω
    • Discuss
    • 4. How much resistance is required to limit the current from a 12 V battery to 3.6 mA?

    • Options
    • A. 3.3 kΩ
    • B. 33 kΩ
    • C. 2.2 kΩ
    • D. 22 kΩ
    • Discuss
    • 5. Approximately how many milliamperes of current flow through a circuit with a 40 V source and 6.8 kΩ of resistance?

    • Options
    • A. 27.2 mA
    • B. 59 mA
    • C. 5.9 mA
    • D. 590 mA
    • Discuss
    • 6. How much current is produced by a voltage of 18 kV across a 15 kΩ resistance?

    • Options
    • A. 1.2 A
    • B. 12 A
    • C. 120 mA
    • D. 12 mA
    • Discuss
    • 7. If 24 V are applied across a resistor and there are 10.9 mA of current, the resistance is

    • Options
    • A. 220 kΩ
    • B. 22 kΩ
    • C. 2.2 kΩ
    • D. 220 Ω
    • Discuss
    • 8. A resistance of 3.3 MΩ is connected across a 500 V source. The resulting current is approximately

    • Options
    • A. 15.1 µA
    • B. 151 µA
    • C. 66 mA
    • D. 660 mA
    • Discuss
    • 9. If you wish to increase the amount of current in a resistor from 120 mA to 160 mA by changing the 24 V source, what should the new voltage setting be?

    • Options
    • A. 8 V
    • B. 320 V
    • C. 3.2 V
    • D. 32 V
    • Discuss
    • 10. An electric heater draws 3.5 A from a 110 V source. The resistance of the heating element is approximately

    • Options
    • A. 385 Ω
    • B. 38.5 Ω
    • C. 3.1 Ω
    • D. 31 Ω
    • Discuss


    Comments

    There are no comments.

Enter a new Comment