logo

CuriousTab

CuriousTab

Discussion


Home Electronics and Communication Engineering Automatic Control Systems Comments

  • Question
  • For the system in the given figure the characteristic equation is
    For the system in the given figure the characteristic equation is K(s + 1)(s + 3) = 0 s(s + 2) = 0 T


  • Options
  • A. For the system in the given figure the characteristic equation is K(s + 1)(s + 3) = 0 s(s + 2) = 0 T
  • B. For the system in the given figure the characteristic equation is K(s + 1)(s + 3) = 0 s(s + 2) = 0 T
  • C. K(s + 1)(s + 3) = 0
  • D. s(s + 2) = 0

  • Correct Answer
  •  

    Explanation
    Transfer function = For the system in the given figure the characteristic equation is K(s + 1)(s + 3) = 0 s(s + 2) = 0 T.

    Hence characteristic equation is For the system in the given figure the characteristic equation is K(s + 1)(s + 3) = 0 s(s + 2) = 0 T.


    Automatic Control Systems problems


    Search Results


    • 1. In a minimum phase system

    • Options
    • A. all poles lie in the left half plane
    • B. all zeros lie in the left half plane
    • C. all poles lie in the right half plane
    • D. all except one pole or zero lie in the left half plane
    • Discuss
    • 2. When a unit step voltage drives a lag network the output

    • Options
    • A. remains constant at unit step value
    • B. increases exponentially from zero to final value
    • C. decreases exponentially from 1 to 0
    • D. either (b) of (c) depending on values of R and C
    • Discuss
    • 3. Consider the systems with following open loop transfer functions

      If unity feedback is used, the increasing order of time taken for unit step response to settle is

    • Options
    • A. 1, 2, 3
    • B. 3, 1, 2
    • C. 2, 3, 1
    • D. 3, 2, 1
    • Discuss
    • 4. First column elements of Routh's tabulation are 3, 5, , 2. It means that there

    • Options
    • A. is one root in left half s plane
    • B. are two roots in left half s plane
    • C. are two roots in right half s plane
    • D. is one root in right half s plane
    • Discuss
    • 5. For the control system in the given figure, the value of K for critical damping is

    • Options
    • A. 1
    • B. 5.125
    • C. 6.831
    • D. 10
    • Discuss
    • 6. Mechanical impedance is the ratio of

    • Options
    • A. rms force to rms velocity
    • B. rms force to rms displacement
    • C. rms velocity to rms displacement
    • D. none of the above
    • Discuss
    • 7. In a radio receiver with simple AGC

    • Options
    • A. the highest AGC voltage is produced between stations
    • B. the faster the AGC time constant, the more accurate the output
    • C. an increase in signal strength produces more AGC
    • D. the audio stage gain is normally controlled by AGC
    • Discuss
    • 8. In a superheterodyne receiver, the IF is 455 kHz. If it is tuned to 1200 kHz, the image frequency will be

    • Options
    • A. 1655 kHz
    • B. 2110 kHz
    • C. 745 kHz
    • D. 910 kHz
    • Discuss
    • 9. In a broadcast superheterodynes receiver having no RF amplifier, the loaded Q of the antenna coupling circuit is 100. If the intermediate frequency is 455 kHz. The image frequency at 25 MHz will be

    • Options
    • A. 24.09 MHz
    • B. 24.54 MHz
    • C. 25.45 MHz
    • D. 25.91 MHz
    • Discuss
    • 10. Noise generated in a resistor is also known as

    • Options
    • A. partition noise
    • B. white noise
    • C. thermal noise
    • D. shot noise
    • Discuss


    Comments

    There are no comments.

Enter a new Comment