logo

CuriousTab

CuriousTab

Discussion

Home ‣ Certification ‣ CISCO Certification Comments
  • Question

  • A wireless client cannot connect to an 802.11b/g BSS with a b/g wireless card. The client section of the access point does not list any active WLAN clients. What is a possible reason for this?


  • Options
  • A. The incorrect channel is configured on the client
  • B. The Client's IP address is on the wrong subnet
  • C. The client has an incorrect pre-shared key
  • D. The SSID is configured incorrectly on the client

  • Correct Answer
  • The SSID is configured incorrectly on the client 

    Explanation

    Although this question is cryptic at best, the only possible answer is option D. If the  SSID is not being broadcast (which we must assume in this question), the client must be configured with the correct SSID in order to associate to the AP.

    • CISCO Certification problems

    Search Results

    • 1. What is the maximum data rate for the 802.11g standard?

    • Options
    • A. 6Mbps
    • B. 11Mbps
    • C. 22Mbps
    • D. 54Mbps
      • Discuss
    • 2. Which encryption type does WPA2 use?

    • Options
    • A. AES - CCMP
    • B. PPK via IV
    • C. PSK
    • D. TKIP/MIC
      • Discuss
    • 3. You have finished physically installing an access point on the ceiling of your office. At a minimum, which parameter must be configured on the access point in order to allow a wireless client to operate on it?

    • Options
    • A. AES
    • B. PSK
    • C. SSID
    • D. WEp
      • Discuss
    • 4. What is the frequency range of the IEEE 802.11g standard?

    • Options
    • A. 2.4 Gbps
    • B. 5Gbps
    • C. 2.4GHz
    • D. 5GHz
      • Discuss
    • 5. In thefollowing output, what type of NAT is being used? ip nat pool todd-nat 170.168.10,10 170.168.10.20 netmask 255.255.255.0
    • Discuss
    • 6. Two workers have established wireless communication directly between their wireless laptops. What type of wireless topology has been created by these employees?

    • Options
    • A. BSS
    • B. SSID
    • C. IBSS
    • D. ESS
      • Discuss
    • 7. You are connecting an access point and it is set to root. What does extended service set ID mean?

    • Options
    • A. That you have more than one access point and they are in the same SSID connected by a distribution system
    • B. That you have more than one access point and they are in seperate SSIDs connected by a distribution system
    • C. That you have multiple access points, but they are placed physically in different buildings
    • D. That you have multiple access points, but one is a repeater access point
      • Discuss
    • 8. How many bits are in an IPv6 address field?

    • Options
    • A. 24
    • B. 16
    • C. 32
    • D. 128
      • Discuss
    • 9. Which of the following descriptions about IPv6 is correct?

    • Options
    • A. Addresses are not hierarchical and are assigned at random
    • B. Broadcasts have been eliminated and replaced with multicasts
    • C. There are 2.7 billion addresses
    • D. An interface can only be configured with one IPv6 address
      • Discuss
    • 10. To enable OSPFv3, which of the following would you use?

    • Options
    • A. Router1 (config - if) # ipv6 ospf 10 area 0.0.0.0
    • B. Router1 (config - if) # ipv6 router rip 1
    • C. Router1 (config - if) # ipv6 router eigrp 10
    • D. Router1 (config - if) # ospf ipv6 10 area 0
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.