Discussion
Home ‣ Certification ‣ CISCO Certification Comments
- Question
If one of the host connected to Sw-AC3 wants to send message to ip 190.0.2.5 (or any ip on a different subnet) what will be the destination MAC address ?
- Correct Answer
- and Explanation: Because the destination address is on a different subnet from the switch, the packet will be forwarded to its default gateway To verify the default gateway of this switch, use the show running-config command From the output above, we can see that its default-gateway is 1921681254 Which can be said to be a layer 3 device (router); in this case, the VLAN-R1 router You can use the show cdp neighbor detail command verify further From the output above, you can confirm that the switch's default gateway is VLAN-R1 router (with the IP address of 1921681254)The interface FastEthernet0/3 shows that the switch is directly connected to VLAN-R1 router through the switchport Fa0/3 To verify the MAC address associated this interface is interface, you use the show mac-address-table command: Looking closely at the table above, you will discorver that the corresponding MAC address is 000ab7e98360 Although there are some entries on port Fa0/3 with different Vlans ,but they have the same MAC address From the output above, you can confirm that the switch's default gateway is VLAN-R1 router (with the IP address of 1921681254)The interface FastEthernet0/3 shows that the switch is directly connected to VLAN-R1 router through the switchport Fa0/3 To verify the MAC address associated this interface is interface, you use the show mac-address-table command
- 1. Your company wants to reconfigure a Catalyst 2950. Which actions must be taken to erase the old configuration?(Choose three) A. Erase flash B. Restart the switch C. Delete the VLAN database D. Erase the startup configuration Discuss
- 2. You have the following binary number :10110111. What are the decimal and hexadecimal equivalents?
Options- A. 69/0x2102
- B. 183/B7
- C. 173/A6
- D. 83/0xC5 Discuss
- 3. What type of RJ45 UTP cable do you use to connect a PC's COM port to a router or switch console port?
Options- A. Straight - through
- B. Crossover cable
- C. Crossover with a CSU/DSU
- D. Rolled Discuss
- 4. Differentiate a MAC address and an IP address and describe how and when each address type is used in a network? Discuss
- 5. What is the bit length and expression form of a MAC address? Discuss
- 6. Which three IP addresses can be assigned to hosts if the subnet mask is /27 and subnet zero is usable? A. 10.15.32.17 B. 17.15.66.128 C. 66.55.128.1 D. 135.1.64.34 E. 129.33.192.192 F. 192.168.5.63 Discuss
- 7. Differentiate types of Ethernet cabling and identify their proper application? Discuss
- 8. If you use either Telnet or FTP, what layer are you using to generate the data?
Options- A. Application
- B. Presentation
- C. Session
- D. Transport Discuss
- 9. The DoD model (also called the TCP/IP stack) has four layers. Which layer of the DoD model is equivalent to the Network layer of the OSI model?
Options- A. Application
- B. Host-to-Host
- C. Internet
- D. Network Access Discuss
- 10. Which of the following protocols uses both TCP and UDP?
Options- A. FTP
- B. SMTP
- C. Telnet
- D. DNS Discuss
CISCO Certification problems
Search Results
Correct Answer: Answer: B C D
Correct Answer: 183/B7
Explanation:
You must be able to take a binary number and convert it into both decimal and hexadecimal. To convert to decimal, just add up the 1s using their values. The values that are turned on with the binary number of 10110111 are 128+32+16+4+2+1=183. To get the hexadecimal equivalent, you need to break the eight binary digits into nibbles (4 bits), 1011 and 0111. By adding up these values, you get 11 and 7. In hexadecimal, 11 is B, so the answer is 0xB7.
Correct Answer: Rolled
Explanation:
To connect to a router or switch console port, you would use an RJ45 UTP rolled cable.
Correct Answer: A MAC address is a hexadecimal number identifying the physical connection of a host MAC addresses are said to operate on layer 2 of the OSI model IP addresses, which can be expressed in binary or decimal format, are logical identifiers that are said to be on layer 3 of the OSI model Hosts on the same physical segment locate one another with MAC addresses, while IP addresses are used when they reside on different LAN segments or subnets Even when the hosts are in different subnets , a destination IP address will be converted to a MAC address when the packet reaches the destination network via routing
Correct Answer: 48 bits (6 bytes) expressed as a hexadecimal number
Correct Answer: : A C D Explanation: If you follow the cram table, /27 is mask 255255255224 3 bits were borrowed with value of 32 Follow the fourth octets of the addresses: A is a usable host address B is classified as a network address C is a usable host address form the subnet 0 D is a usable host address E is a network address F is a broadcast address
Correct Answer: The three types of cables that can be created from an Ethernet cable are straight-through (to connect a PC's or a router's Ethernet interface to a hub or switch), crossover (to connect hub to hub , hub to switch, switch to switch, or PC to PC), and rolled (for a console conection from a PC to a router or switch)
Correct Answer: Application
Explanation:
Both FTP and Telnet use TCP at the Transport layer; however, they both are Application layer protocols, so the Application layer is the best answer for this question.
Correct Answer: Internet
Explanation:
The four layers of the DoD model are Application/process, Host-to-Host, Internet, and Network Access. The Internet layer is equivalent to the Network layer of the OSI model.
Correct Answer: DNS
Explanation:
DNS uses TCP for zone exchanges between servers and UDP when a client is trying to resolve a hostname to an IP address.
Comments
There are no comments.Programming
Copyright ©CuriousTab. All rights reserved.