CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Irrigation problems
1. Which one of the following statements is correct?
Options
A. The canal system and the drainage system are complementary
B. The canal system runs on ridges, gets divided into smaller channels and spreads its water on the land
C. The drainage system runs along the lowest line, collects drainage water from the slopes and joins the main stream
D. All the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: All the above.
2. For cereal crops the most commonly adopted method of irrigation, is
Options
A. free flowing method
B. check method
C. furrow method
D. sprinkling method.
Show Answer
Scratch Pad
Discuss
Correct Answer: check method
3. In case of a trapezoidal notch fall
Options
A. top width of the notch is kept between 3/4 th of full water depth above the sill of the notch
B. top length of the piers should not be less than their thickness
C. splay up stream from the notch section is 45°
D. splay down stream from the notch section is
E. all the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: all the above.
4. A counter berm is
Options
A. a horizontal benching provided on the inside slope
B. a horizontal benching provided on the outside slope
C. a vertical benching provided on the outer edge of the bank
D. a vertical benching provided on the inner edge of the bank.
Show Answer
Scratch Pad
Discuss
Correct Answer: a horizontal benching provided on the outside slope
5. If
D
1
and
D
2
are depths of water upstream and down stream of a hydraulic jump, the loss of head at the jump, is
Options
A.
B.
C.
D.
Show Answer
Scratch Pad
Discuss
Correct Answer:
6. The ratio of the rate of change of discharge of an outlet to the rate of change in level of water surface in a distributary at its normal depth, is known as
Options
A. efficiency
B. sensitivity
C. flexibility
D. modular limit.
Show Answer
Scratch Pad
Discuss
Correct Answer: sensitivity
7. The most suitable section of a lined canal, is
Options
A. triangular section with circular bottom for small canals
B. trapezoidal section with rounded corners for large canals
C. rectangular section with rounded corners for large canals
D. both (a) and (b)
E. both (a) and (c)
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) and (b)
8. In a syphon aqueduct
Options
A. drainage passes over the canal and F.S.L. of the canal is below the bottom of the drainage trough
B. drainage passes over the canal and F.S.L. of the canal is above the bottom of the drainage trough
C. canal passes over the drainage and H.F.L. of the drainage is above the bottom of the canal trough
D. canal passes over the drainage and H.F.L. of the drainage is below the bottom of the canal trough.
Show Answer
Scratch Pad
Discuss
Correct Answer: canal passes over the drainage and H.F.L. of the drainage is above the bottom of the canal trough
9. A current meter measures the velocity of flow, if it is held
Options
A. on the surface of water
B. at the bottom of channel
C. at any point within the cross-section
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: at any point within the cross-section
10. Pick up the correct statement from the following
Options
A. Escapes are essential safety valves in a canal system
B. The capacity of escapes should not be less than the capacity of the canal at its location
C. The escapes must lead the surplus water to natural drainages
D. The escapes are aligned to take advantage of contours of lower values
E. All the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: All the above.
First
14
Last
More in Civil Engineering:
Advanced Surveying
Airport Engineering
Applied Mechanics
Building Construction
Building Materials
Concrete Technology
Construction Management
Docks and Harbours
Elements of Remote Sensing
Engineering Economy
Estimating and Costing
GATE Exam Questions
Highway Engineering
Hydraulics
Irrigation
Railways
RCC Structures Design
SI Units
Soil Mechanics and Foundation Engineering
Steel Structure Design
Strength of Materials
Structural Design Specifications
Surveying
Theory of Structures
Tunnelling
UPSC Civil Service Exam Questions
Waste Water Engineering
Water Resources Engineering
Water Supply Engineering