CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Advanced Surveying problems
1. In a truly vertical photograph,
Options
A. principal point coincides the isocentre
B. iso-centre coincides the plumb point
C. plumb point coincides the principal point
D. principal point, iso-centre and plumb point coincide
E. all the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: all the above.
2. The latitude of a place was obtained by subtracting the zenith distance of a star from its declination, the observed star was between
Options
A. horizon and equator
B. equator and zenith
C. zenith and pole
D. pole and horizon.
Show Answer
Scratch Pad
Discuss
Correct Answer: zenith and pole
3. The want of correspondence in stereo-photographs
Options
A. is a good property
B. is a function of tilt
C. is not affected by the change of flying height between photographs
D. is minimum when ? is 3°.
Show Answer
Scratch Pad
Discuss
Correct Answer: is a function of tilt
4. According to Napier's Rules of circular parts for a right angled triangle, sine of middle part equals the product of
Options
A. tangents of two adjacent parts
B. sines of two adjacent parts
C. cosines of two adjacent parts
D. cosines of two opposite parts
E. both (a) and (b) above.
Show Answer
Scratch Pad
Discuss
Correct Answer: both (a) and (b) above.
5. Pick up the correct statement from the following :
Options
A. The plane passing through the perspective centre of a stereo pair and a ground point, is known as basal plane
B. Each pair of image points on stereo pair have their own basal plane
C. Relative orienation means reconstructing the basal plane
D. Relative orientation of the model is achieved only when five points within the model are cleared of
Y
-parallax
E. All the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: All the above.
6. In triangulation surveys
Options
A. the area is divided into triangular figures
B. control stations are located from which detailed surveys are carried out
C. sides are not measured excepting the base line
D. angular measurements are only resorted to
E. all the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: all the above.
7. Pick up the correct statement from the following :
Options
A. The star's movement is apparent due to the actual steady rotation of the earth about its axis
B. The stars move round in circular concentrated parts
C. The centre of the circular paths of stars is the celestial pole
D. The axis of rotation is a fixed direction of a particular diameter of the celestial sphere either end of which is a pole
E. All the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: All the above.
8. The Polaris describes a small circle round the pole whose radius is approximately
Options
A. 1°
B. 2°
C. 3°
D. 4°.
Show Answer
Scratch Pad
Discuss
Correct Answer: 1°
9. A plate parallel is the line on the plane of the negative
Options
A. parallel to the principal line
B. perpendicular to the principal line
C. along the bisector of the angle between the principal line and a perpendicular line through principal plane
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: perpendicular to the principal line
10. The great circle whose plane is perpendicular to the axis of rotation of the earth, is called
Options
A. equator
B. terrestrial equator
C. 0° latitude
D. all the above.
Show Answer
Scratch Pad
Discuss
Correct Answer: all the above.
First
13
14
15
...
16
..
17
18
Last
More in Civil Engineering:
Advanced Surveying
Airport Engineering
Applied Mechanics
Building Construction
Building Materials
Concrete Technology
Construction Management
Docks and Harbours
Elements of Remote Sensing
Engineering Economy
Estimating and Costing
GATE Exam Questions
Highway Engineering
Hydraulics
Irrigation
Railways
RCC Structures Design
SI Units
Soil Mechanics and Foundation Engineering
Steel Structure Design
Strength of Materials
Structural Design Specifications
Surveying
Theory of Structures
Tunnelling
UPSC Civil Service Exam Questions
Waste Water Engineering
Water Resources Engineering
Water Supply Engineering