logo

CuriousTab

CuriousTab

Discussion


Home Chemical Engineering Process Control and Instrumentation Comments

  • Question
  • In a feed-back control system G and H denote open loop and close loop transfer functions respectively. The output-input relationship is


  • Options
  • A. In a feed-back control system G and H denote open loop and close loop transfer functions respectivel
  • B. In a feed-back control system G and H denote open loop and close loop transfer functions respectivel
  • C. In a feed-back control system G and H denote open loop and close loop transfer functions respectivel
  • D. In a feed-back control system G and H denote open loop and close loop transfer functions respectivel

  • Correct Answer
  •  


  • Process Control and Instrumentation problems


    Search Results


    • 1. A stable system is the one

    • Options
    • A. for which the output response is bounded for all bounded input.
    • B. which exhibits an unbounded response to a bounded input
    • C. which satisfies the conditions for a servo problem.
    • D. none of these.
    • Discuss
    • 2. The pressure sensing element of elastic type pressure gauge is never made in the form of a

    • Options
    • A. bellow
    • B. diaphragm
    • C. strip
    • D. Bourdon tube
    • Discuss
    • 3. The Laplace transform of exp(at), where a > 0, is defined only for the Laplace parameter, s > a since

    • Options
    • A. the function is exponential.
    • B. the Laplace transform of integral of exp(at) has finite values only for s > a.
    • C. the Laplace transform integral of exp(at) has initial values only for s > a.
    • D. the function exp(at) is piece-wise continuous only for s > a.
    • Discuss
    • 4. Photoelectric pyrometers are suitable in the temperature range of __________ °C.

    • Options
    • A. 400-1600
    • B. 800-1600
    • C. 800-2500
    • D. 400-1000
    • Discuss
    • 5. Which of the following thermocouples is capable of measuring a temperature of -50°C?

    • Options
    • A. Platinum - platinum + rhodium
    • B. Chromel - alumel
    • C. Iron-constantan
    • D. Copper - constantan
    • Discuss
    • 6. Bourdon tube is never made of

    • Options
    • A. phosphor bronze
    • B. monel metal
    • C. stainless steel
    • D. cast iron
    • Discuss
    • 7. Hot wire anemometer is used for the measurement of

    • Options
    • A. flow rates of fluids.
    • B. flow rates of granular solids.
    • C. very high temperature.
    • D. thermal conductivity of gases.
    • Discuss
    • 8. In a shell and tube heat exchanger, the outlet temperature of heating/cooling fluid is the __________ variable.

    • Options
    • A. load
    • B. manipulated
    • C. controlled
    • D. none of these
    • Discuss
    • 9. Find the ultimate gain and frequency for a proportional controller in the case of a process having the transfer function Gp(s) = 1/(4s + 1)(2s + 1)(s + 1).

    • Options
    • A. w = 1/14, Kc = 45/714
    • B. w = 7/6, Kc = 46/3
    • C. w = 1, Kc = 13
    • D. w = 7/8, Kc = 45/4
    • Discuss
    • 10. Response of a linear control system for a change in set point is called

    • Options
    • A. frequency response
    • B. transient response
    • C. servo problem
    • D. regulator problem
    • Discuss


    Comments

    There are no comments.

Enter a new Comment