logo

CuriousTab

CuriousTab

Discussion

Home ‣ Chemical Engineering ‣ Process Control and Instrumentation Comments
  • Question

  • Pressure of 0.01 psi (absolute) can be measured by __________ gauge.


  • Options
  • A. ionisation
  • B. Pirani
  • C. Mcloid
  • D. none of these

  • Correct Answer
  • Mcloid 

    • Process Control and Instrumentation problems

    Search Results

    • 1. On-off controllers are normally used for

    • Options
    • A. low loads
    • B. temperature changes
    • C. flow rate changes
    • D. none of these
      • Discuss
    • 2. Which of the following is a 'contact' pyrometer?

    • Options
    • A. resistance pyrometer
    • B. optical pyrometer
    • C. radiation pyrometer
    • D. infra red pyrometer
      • Discuss
    • 3. What is the dynamic error in a critically damped second order instrument for a ramp input (At)?

    • Options
    • A. 0.5 AT
    • B. 2 AT
    • C. AT
    • D. 1.5 AT
      • Discuss
    • 4. A process is initially at steady state with its output y=l for an input u=l. The input is suddenly changed to 2 at time t=0. The output response is y(t)=1+2t. The transfer function of the process is

    • Options
    • A. 2/s
    • B.
    • C.
    • D.
      • Discuss
    • 5. Measurement of pressure in ammonia reactor is done by

    • Options
    • A. Bourdon gauge
    • B. U-tube manometer
    • C. Inclined tube manometer
    • D. Pirani guage
      • Discuss
    • 6. For increased speed of response of an expansion pressure spring thermometer, the thermometer bulb should have a

    • Options
    • A. large area but small mass.
    • B. high thermal conductivity.
    • C. small specific heat.
    • D. all'a', 'b' & 'c'.
      • Discuss
    • 7. Pressure of 0.0001 absolute psi can be measured by __________ gauge.

    • Options
    • A. Mcloid
    • B. Pirani
    • C. thermocouple
    • D. none of these
      • Discuss
    • 8. For the block diagram shown below :

      The characteristic equation is

    • Options
    • A. ?l S (?ps + 1) + Kc . Kp (?lS + 1) e-?d s = 0
    • B. (?mS + 1) (?pS + 1) + Km . Kp e-?d S = 0
    • C. ?l S(?m S + 1) (?p S + 1) +Kc . Kp . Km (?l s + 1) e-?dS = 0
    • D. (?ms + 1) (?p s + 1) + Kc . Kp . Km . e-?dS = 0
      • Discuss
    • 9. An ideal PID controller has the transfer function . The frequency at which the magnitude ratio of the controller is 1, is

    • Options
    • A. 0.5/0.2
    • B. 0.2/0.5
    • C. 0.2 x 0.5
    • D. 1/0.2 x 0.5
      • Discuss
    • 10. Continuous measurement of moisture in paper is done by

    • Options
    • A. sling psychrometer.
    • B. hair-hygrometer.
    • C. weighing.
    • D. high resistance Wheatstone's bridge circuit.
      • Discuss

    Comments

    There are no comments.
Enter a new Comment




Aptitude

Engineering

Programming

Reasoning

Links

Copyright ©CuriousTab. All rights reserved.