CuriousTab
Search
CuriousTab
Home
Aptitude
Computer
C Programming
C# Programming
C++ Programming
Database
Java Programming
Networking
Engineering
Biochemical Engineering
Biochemistry
Biotechnology
Chemical Engineering
Civil Engineering
Computer Science
Digital Electronics
Electrical Engineering
Electronics
Electronics and Communication Engineering
Mechanical Engineering
Microbiology
Technical Drawing
GK
Current Affairs
General Knowledge
Reasoning
Data Interpretation
Logical Reasoning
Non Verbal Reasoning
Verbal Ability
Verbal Reasoning
Exams
AIEEE
Bank Exams
CAT
GATE
IIT JEE
TOEFL
Jobs
Analyst
Bank PO
Database Administrator
IT Trainer
Network Engineer
Project Manager
Software Architect
Discussion
Home
‣
Chemical Engineering
‣
Petroleum Refinery Engineering
Comments
Question
The vacuum maintained in vacuum distillation unit for reduced crude is about __________ mmHg.
Options
A. 1.2
B. 12
C. 120
D. 700
Correct Answer
120
Petroleum Refinery Engineering problems
Search Results
1. The most suitable solvent for deasphalting vacuum residue is
Options
A. propane
B. methyl ethyl ketone
C. doctor's solution
D. methanol amine
Show Answer
Scratch Pad
Discuss
Correct Answer: methyl ethyl ketone
2. Pressure & temperature maintained in catalytic cracking is about
Options
A. 2atm & 500°C
B. 10atm & 500°C
C. 30atm & 200°C
D. 50atm. & 750°C
Show Answer
Scratch Pad
Discuss
Correct Answer: 2atm & 500°C
3. Highest quality bitumen is produced from the __________ crude oil.
Options
A. paraffinic
B. naphthenic
C. intermediate
D. mixed
Show Answer
Scratch Pad
Discuss
Correct Answer: naphthenic
4. Which of the following has the lowest cetane number?
Options
A. Aromatics
B.
i
-paraffins
C. Naphthene
D. Olefins
E.
n
-paraffins
Show Answer
Scratch Pad
Discuss
Correct Answer: Aromatics
5. Good quality kerosene should have
Options
A. low smoke point.
B. high smoke point.
C. high aromatics content.
D. low paraffins content.
Show Answer
Scratch Pad
Discuss
Correct Answer: high smoke point.
6. Cetane number of a diesel fuel is the measure of its
Options
A. ignition delay
B. smoke point
C. viscosity
D. oxidation stability
Show Answer
Scratch Pad
Discuss
Correct Answer: ignition delay
7. Clay treatment is used to remove
Options
A. salt from the crude oil.
B. colour & dissolved gases from cracked gasoline.
C. wax from lube oil.
D. none of these.
Show Answer
Scratch Pad
Discuss
Correct Answer: colour & dissolved gases from cracked gasoline.
8. Pick out the wrong statement.
Options
A. Pensky-Marten apparatus is used for determining flash points above 50°C.
B. Characterisation factor of paraffinic crude oil is more than 12.
C. Abel apparatus is used for determining flash points below 50°C.
D. An oil having high susceptibility to change in viscosity with temperature changes, has a high viscosity index.
Show Answer
Scratch Pad
Discuss
Correct Answer: An oil having high susceptibility to change in viscosity with temperature changes, has a high viscosity index.
9. 1 centistoke is equal to __________ Redwood I seconds.
Options
A. 1
B. 4.08
C. 0.408
D. 40.8
Show Answer
Scratch Pad
Discuss
Correct Answer: 4.08
10. Gasoline yield in catalytic reforming of naphtha may be about __________ percent by weight.
Options
A. 85
B. 65
C. 50
D. 98
Show Answer
Scratch Pad
Discuss
Correct Answer: 85
Comments
There are no comments.
Enter a new Comment
Save
More in Chemical Engineering:
Chemical Engineering Basics
Chemical Engineering Plant Economics
Chemical Engineering Thermodynamics
Chemical Process
Chemical Reaction Engineering
Environmental Engineering
Fertiliser Technology
Fluid Mechanics
Fuels and Combustion
Furnace Technology
Heat Transfer
Mass Transfer
Materials and Construction
Mechanical Operations
Nuclear Power Engineering
Petroleum Refinery Engineering
Polymer Technology
Process Control and Instrumentation
Process Equipment and Plant Design
Refractory Technology
Stoichiometry